Extron electronics AXI 22 AT D Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 45

Extron electronics AXI 22 AT D Скачать руководство пользователя страница 26

AXI 22 AT and AXI 44 AT • Dante Controller

20

Dante Controller

This section discusses Dante Controller, the software used to configure a Dante network
and route audio between Dante-enabled devices on the same network. The following topics
are discussed:

•

Downloading and Installing Dante Controller

•

Configuring the AXI in Dante Controller

•

Physical Dante Network Setup

•

Dante Controller Operation

Downloading and Installing Dante Controller

Dante Controller from Audinate is required to select and route digital inputs and outputs to
connected Dante-enabled devices and for limited configuration of the device. Install Dante
Controller on a PC running Microsoft

®

Windows

®

7 or newer. For full details about computer

requirements, see the Dante Controller product page on the Extron website. Dante
Controller is available at

www.extron.com

.

To download Dante Controller:

1.

From

www.extron.com

, click the

Download

tab (see figure 20,

1

).

2.

On the left sidebar, click the

Dante Controller

link (

2

). The

Dante Controller

page opens (see

figure 21

on the next page).

Figure 20.

Accessing the Dante Controller Download Page

figure 20

Accessing Dante Download Page

«
...
24
25
26
27
28
...
»

Содержание AXI 22 AT D














































Отзывы:

Нет отзывов