Extreme Networks ExtremeWireless AP560h Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 40

Extreme Networks ExtremeWireless AP560h Скачать руководство пользователя страница 37

reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•

This device may not cause harmful interference .

•

This device must accept any interference received, including interference that may cause undesired
operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

Regulatory and Compliance Information

FCC Caution:

ExtremeWireless™ AP560h Access Point

37

«
...
35
36
37
38
39
...
»

Содержание ExtremeWireless AP560h









































Отзывы:

Нет отзывов