Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 413

background image

5 Push the power supply in until the latch snaps into place.

Caution
Do not slam the power supply into the switch.

6 To install a second power supply, repeat the procedure.

Note
If power supplies are not installed in both power supply bays, be sure to install a cover
over the unoccupied bay. Unoccupied bays must always be covered to maintain proper
system ventilation and EMI levels.

7 Connect the AC power cord to the input connector on the power supply.

Warning
Always be sure that the source outlet is properly grounded before plugging the AC power
cord into the AC power supply.

8 Connect power. See

Connecting Power to the Switch

Installing a 350 W, 715 W, 770 W, 1100 W, or 2000 W Internal AC Power Supply

Warning
To prevent an electrical hazard, make sure that the AC power cord is not connected to the
power supply before you install the power supply in the power supply bay.

Caution
Make sure the AC power supply circuit is not overloaded. Use proper overcurrent protection,
such as a circuit breaker, to prevent overcurrent conditions.

An AC power cord is not included with the AC power supply. You can purchase AC power cords for use
in the US and Canada from Extreme Networks or from your local supplier. The cord must meet the
requirements listed in

Power Cord Requirements for AC-Powered Switches and AC Power Supplies

page 393.

To install a 350 W, 715 W, 770 W, 1100 W, or 2000 W AC power supply in a switch, follow these steps:

1 If necessary, remove a blank panel from the back of the switch.
2 Verify that the power supply is right side up.
3 Verify that the power supply's airflow direction (front-to-back or back-to-front) is compatible with

the switch.

4 Carefully slide the power supply all the way into the power supply bay, as shown in

Figure 170: Installing a Summit AC Power Supply (770 W Model Shown)

Installing Your Extreme Networks Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

218

«
...
216
217
218
219
220
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: tbs electronics Страницы: 2

Бренд: Gavita Страницы: 12

ATLONA Omega AT-OME-MS52W

Бренд: Panduit Страницы: 123

Atlona AT-OME-MS42

Бренд: Panduit Страницы: 86

VNLW-P-1001-MV-N-V

Бренд: Greengate Страницы: 2

HD Flash 4 KD-SW4x1

Бренд: Key Digital Страницы: 12

STI Echotel 919

Бренд: Magnetrol Страницы: 12

Бренд: Vega Страницы: 44

Бренд: Extron electronics Страницы: 3

Бренд: N-Tron Страницы: 196

24-Port Gigabit Switch

Бренд: Belkin Страницы: 2

S5560S-EI Series

Бренд: H3C Страницы: 47

Бренд: IDT Страницы: 158

Бренд: Konig Страницы: 40

Бренд: QSFPTEK Страницы: 8

Бренд: Conrad Страницы: 8

Бренд: ATEN Страницы: 68

Бренд: Gigacore Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды