Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 413

background image

Installing a 750 W Internal DC Power Supply

Caution
Make sure that the DC power supply circuit is not overloaded. Use proper overcurrent
protection, such as a circuit breaker, to prevent overcurrent conditions. You may use up to a
30-Amp breaker.

To install a 750 W DC power supply in a switch, perform the following tasks in the order listed:

1 Make sure you have the tools and materials you need.

Required Tools and Materials for Installing a 750 W DC Power Supply

on page 202.

2 Prepare the power cables and ground cable by stripping off the insulation.

Preparing the Cables for a 750 W DC Power Supply

3 Ground the switch chassis.

Grounding the Switch Chassis

on page 203.

4 Insert the power supply into the switch.

Installing a 750 W Internal DC Power Supply

on page 202.

5 Connect the ground wire.

Connecting the Ground Wire to a 750 W DC Power Supply

on page 204.

6 Connect the power supply to the DC source voltage.

Connecting a 750 W DC Power Supply to the Source Voltage

7 Energize the DC circuit.

Required Tools and Materials for Installing a 750 W DC Power Supply

You need the following tools and materials to install or remove a 750 W DC power supply in an
ExtremeSwitching X695 switch.

•

#14 AWG copper cable for grounding the power supply and connecting the power supply to the DC
power source. (DC power cables and grounding cables are not included with the power supply.)
Recommended insulation colors are:

•

Red for the –48 V connection (–)

•

Black for the –48 V RTN connection (+)

•

Green or green with yellow stripe for the ground connection

•

Connection hardware appropriate to the installation site:

•

Hardware for connecting the power wires to the DC source

•

Hardware for connecting the ground wire to the site grounding point

•

Stripping tool

•

Cross-head (Phillips) torque screwdriver

•

#1 cross-head (Phillips) screwdriver

•

ESD-preventive wrist strap

•

Thermal protective gloves (for removal of a warm power supply)

Preparing the Cables for a 750 W DC Power Supply

You will need three cable wires for each installed DC power supply: two input cables and a grounding
cable. We recommend that each cable have differently colored insulation, as described in

Tools and Materials for Installing a 750 W DC Power Supply

on page 202.

Installing Your Extreme Networks Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

202

«
...
200
201
202
203
204
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: AbleNet Страницы: 2

BNI IOL-314-S52-P012

Бренд: Balluff Страницы: 22

Бренд: G&D Страницы: 36

Бренд: Eaton Страницы: 40

Бренд: NETGEAR Страницы: 36

Бренд: ATEN Страницы: 2

Бренд: 3onedata Страницы: 2

Бренд: H3C Страницы: 57

Бренд: Avid Technology Страницы: 34

Бренд: Hama Страницы: 14

Бренд: KYLAND Страницы: 34

Бренд: TRENDnet Страницы: 2

PICO-GUARD SFI-D1EDPXT6

Бренд: Banner Страницы: 2

Бренд: SmartAVI Страницы: 2

ISCOM2600G (A) Series

Бренд: Raisecom Страницы: 96

IDS-105FE Series

Бренд: Perle Страницы: 2

Бренд: B&B Electronics Страницы: 2

AVS-OCT-4832-117

Бренд: AMX Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды