Extreme Networks ExtremeSwitching X435 Series Скачать руководство пользователя страница 244

Страница: 244 / 496

The DC power connection at your facility must be made by a qualified electrician, following these
instructions.

Warning
Always make sure that the DC circuit is de-energized before connecting or disconnecting the
DC power cables on the DC power supply.

Caution
Provide proper connection and strain relief on the DC power cables in accordance with all
local and national electrical codes.

1. Verify that the DC circuit is de-energized.
2. Attach an ESD-preventive wrist strap to your bare wrist and connect the metal end to an

appropriate ground point on the rack.

3. Connect the negative wire (–48 V) to the power supply as follows:

a. Insert the stripped end of the wire all the way into the leftmost of the three slots on the terminal

block.
Refer to

Figure 190

for slot locations.

Figure 190: Slots for Connecting Wires to the 750 W DC Power Supply

b. Insert a #1 Phillips screwdriver into the hole below the slot, and tighten.
c. Gently tug the wire to make sure it is fastened securely.

4. Connect the positive wire (–48 V) as follows:

a. Insert the stripped end of the wire all the way into the rightmost of the three slots on the

terminal block.

b. Insert a #1 Phillips screwdriver into the hole below the slot, and tighten.
c. Gently tug the wire to make sure it is fastened securely.

5. Connect the cables to the DC source voltage, using hardware appropriate to the installation site and

following local and national electrical codes.

Turn on the switch, following the steps in

Connecting Power to the Switch

on page 258.

Leave the ESD strap permanently connected to the rack, so that the strap is always available when you
need to handle ESD-sensitive components.

Installing a 750 W Internal DC Power Supply

Installing Your Extreme Networks Switch

244 ExtremeSwitching Hardware Installation Guide

Содержание ExtremeSwitching X435 Series

















































































































































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X435 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X435 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X435 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X435 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X435 Series

Бренды по названию

Популярные бренды