Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 50

Страница: 50 / 135

3. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).

FIGURE 30

Attaching the rear brackets to the front rack posts

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

Installing the 1U, 1.5U, and 2U Mid-Mount Kit for

Two-Post Racks (XBR-000165, XBR-000175, and

XBR-R000292)

Use the following instructions to install a fixed-port device in a mid-mount configuration in a two-post rack using the 1U, 1.5U, and 2U
Mid-Mount Kit for Two-Post Racks (XBR-000165, XBR-000175, and XBR-R000292).

Observe the following when mounting this device:

•

Two people are required to install the device in a rack. One person holds the device, while the other secures the device to the
rack.

•

Before mounting your device, review any specific installation and facility requirements in this Hardware Installation Guide.

Installing the 1U, 1.5U, and 2U Mid-Mount Kit for Two-Post Racks (XBR-000165, XBR-000175, and XBR-R000292)

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды