Extreme Flight Turbo Bushmaster Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 27

Extreme Flight Turbo Bushmaster Скачать руководство пользователя страница 6

6

3. Apply a generous portion of 30-minute epoxy to the aileron and flap control horn slots

and to the scuffed area of the control horns. It may be helpful to use a zip tie to push the

epoxy into the slots.

4. Assemble the control horns and ball links as shown and install the control horns into

their respective slots. Wipe away any excess epoxy with a paper towel or cloth soaked

with denatured alcohol.

5. In these next steps we will install the hinges. Please take a few moments to familiarize

yourself with this process if you have not installed hinge points before.

There are several ways to do this and several adhesives you can use. We will describe the

way that we do it, as this method has proven itself over many years of model building. If

you are new to this type of hinging process, then I recommend that you install a single

hinge first just to acquaint yourself with this method

Before starting you will need to gather a few items to aid you as you proceed.

A.

30 Minute Epoxy

B.

A short length of pushrod or small dowel.

C.

A roll of paper towels

D.

Denatured alcohol or Acetone

E.

Hobby Knife

F.

Teflon lubricant

«
...
4
5
6
7
8
...
»

Содержание Turbo Bushmaster




























Отзывы:

Нет отзывов