background image

11

ENGLISH

NotEs For CorrECt opErAtIoN 

Pellet hopper lid

Fire door

For the correct operation of the pellet stove, the following 

indications must be respected:

Both during the functioning and when the stove is not in use, 

all the machine doors (pellet hopper, fire door, ash drawer) must 

always remain closed.  The machine doors can only be opened 

for the time required to load the pellet and for maintenance.

Failure to comply with that above during operation will cause 

the display to show the following:

"CLOSE HOPPER-DOOR" 

This message indicates that you have 60 seconds to close the 

hatch/door and pellet lid.

After the 60 seconds, during the ignition phase the stove will 

go to "DEPR ALARM" mode, while during normal operation the 

stove will go to "COOLING STAND BY" mode and then re-start 

automatically when the correct conditions are present (stove 

cold, etc.).

posItIoNING tHE stovE

For the correct operation of the product, we recommend positioning it on a perfectly flat surface. Use a spirit level to check this.

FUsE

If the stove is not powered, check the condition of the fuse in the drawer between the stove switch and the power cord.

Содержание LUCIA





































Отзывы: