background image

MN47-EU-EN-V3.0–12/11 

14

GENERAL SPECIFICATIONS 

Display 

4000 count LCD with function indication 

Over-range indication

 

“OL” is displayed 

Auto Power Off 

After 15 minutes (approximately) of inactivity 

Polarity

 

Automatic (no indication for positive); Minus (-) sign for negative 

Input Impedance

 >1M

 

ACV Bandwidth 

45Hz to 450Hz 

DCA voltage drop 

200mV 

NCV voltage range 

100VAC to 600VAC 

Audible continuity

Audible threshold: less than 30

; Test current: <0.3mA 

Measurement Rate 

2 times per second, nominal 

Low Battery Indication 

“BAT” is displayed when battery voltage drops below operating level.  

Battery

 

One (1) 9V (NEDA 1604) IEC 6F22 battery

 

Fuses

  

mA, µA ranges; 0.5mA/250V fast blow 
A range; 10A/250V fast blow 

Operating Temperature

 

32ºF to 122ºF (0ºC to 50ºC) 

Storage Temperature

 -4

o

F to 140

o

F (-20

o

C to 60

o

C) 

Operating Humidity 

<70% RH 

Storage Humidity 

<80% RH 

Operating Altitude 

7000ft. (2000meters) maximum. 

Weight

  

8.99 oz (255g) 

Size  

5.9” x 2.8” x 1.9” (150 x 70 x 48mm)

 

Safety

  

This meter is intended for indoor use and protected, against the users, 

by class 2 double insulation per EN61010-1. CAT III 600V  

 

PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY 

OVERVOLTAGE CATEGORY I 

Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in which 
measures are taken to limit the transient overvoltages to an appropriate low level. Note – Examples 
include protected electronic circuits. 

OVERVOLTAGE CATEGORY II 

Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be supplied from 
the fixed installation. 
Note – Examples include household, office, and laboratory appliances. 

OVERVOLTAGE CATEGORY III 

Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations. 
Note – Examples include switches in the fixed installation and some equipment for industrial use 
with permanent connection to the fixed installation. 

OVERVOLTAGE CATEGORY IV 

Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation. 
Note – Examples include electricity meters and primary over-current protection equipment 
 
 

Copyright 

©

 2011 Extech Instruments Corporation (a FLIR company) 

All rights reserved including the right of reproduction in whole or in part in any form. 

 

Содержание MN47















Отзывы: