background image

EXTECH INSTRUMENTS 

2

                                       

MA610-en-GB_V1.0   12/16

 

Introduction 

Thank  you  for  selecting  the  Extech  MA610  Clamp  Meter.  This  meter  measures  AC  Current, 
AC/DC Voltage, Resistance, Capacitance, Frequency, Diode Test, Duty Cycle, Continuity and Non-
Contact  Voltage  detection.  This  device  is  shipped  fully  tested  and  calibrated  and,  with  proper 
use, will provide years of reliable service.

Features 

 

Large backlit LED display 

 

30mm (1.2") jaw size fits conductors up to 500MCM 

 

Relative and Zero mode functionality 

 

Auto Power OFF (APO) 

 

Non-Contact Voltage Detector 

 

Visual and audible continuity measurement alert 

 

Low battery indicator  

 

CAT III 600V 

Safety 

To ensure the safe operation and service of the meter, follow these instructions closely. Failure to 
observe warnings can result in severe injury. 

WARNINGS 

WARNINGS identify hazardous conditions and actions that could cause BODILY HARM or DEATH. 

 

When handling test leads or probes, keep hands and fingers behind the finger guards at all times. 

 

Remove test leads from the meter before opening the battery compartment or meter housing. 

 

Use the meter only as specified in this User Manual or accompanying Quick Start to avoid compromising 
the protections provided by the meter. 

 

Be sure to use the proper terminals, switch positions, and ranges when taking measurements. 

 

Verify the meter’s operation by measuring a known voltage. Have the meter serviced if the meter 
responds unusually or if there are questions regarding the meter’s functional integrity. 

 

Do not apply more than the rated voltage, as marked on the meter, between terminals or between any 
terminal and earth ground. 

 

Use caution working with voltages above 30 VAC RMS, 42 VAC peak, or 60 VDC. These voltages pose a 
shock hazard. 

 

To avoid misleading readings that could lead to electric shock and injury, replace the batteries as soon as 
the low battery indicator is displayed. 

 

Disconnect power to the circuit under test and discharge all high-voltage capacitors before testing 
resistance, continuity, diodes, or capacitance. 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MA610



















Отзывы: