manualshive.com logo in svg

Extech Instruments CO200, Руководство пользователя

Поделиться
Скачать
Extech Instruments CO200 Скачать руководство пользователя страница 9

9                                          CO200-EU-EN-V1.1-11/11 

 

TROUBLESHOOTING

 

 

Can’t power on:  

Check whether the adaptor is properly plugged in. 

Slow response:  

Check whether the air flow channels on the rear of 
the meter are blocked. 

"BAt” and green LED keep 
flashing:  

The adaptor output voltage is too high or too low. 
Please use the adaptor with correct output. 

 

Error Codes: 

CO

2

 Display 

 

E01  

CO

2

 sensor is damaged  

Send back for repair  

E02  

CO

2

 reading is under the 

lower limit  

Re-calibrate the meter, if it still 
appears, return for repair 

E03  

CO

2

 reading is above the 

upper limit 

Put the meter in fresh air and wait for 
5minutes, if it still appear, re-calibrate 
the meter. If above two methods faile, 
return for repair 

E17 

ABC mode of CO

2

 senor 

has failed and might 
cause wrong CO

2

 

readings 

Send back for repair

 

 

Temp 
Display

 

 

E02  

Air temp. measurement is 
under the lower limit 

Put the meter in regular room 
temperature for 30 minutes, if it still 
appears, return for repair 

E03  

Air temp. measurement is 
over the upper limit  

Put the meter in regular room 
temperature for 30 minutes, if it still 
appears, return for repair 

E31  

Temp. sensor or 
measuring circuit is 
damaged  

Return for repair

 

 

Humidity 
Display 

 

E04  

Air temp. measurement 
has error code 

Refer to temperature error code for 
problem solving 

E11  

The RH calibration has 
failed 

Please return for repair 

E34  

RH sensor or measuring 
circuit has failed  

Return for repair

 

 

Содержание CO200











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды