manualshive.com logo in svg

Extech Instruments 411, Руководство пользователя

Поделиться
Скачать
Extech Instruments 411 Скачать руководство пользователя страница 3

V4.0       5/07 

3 

OVERVOLTAGE CATEGORY III 

This meter meets the IEC 610-1-95 standard for 
OVERVOLTAGE CATEGORY III. Cat III meters are protected 
against overvoltage transients in fixed installation at the 
distribution level. Examples include switches in the fixed 
installation and some equipment for industrial use with 
permanent connection to the fixed installation. 

SAFETY INSTRUCTIONS 

This meter has been designed for safe use, but must be 
operated with caution. The rules listed below must be carefully 
followed for safe operation. 

1. 

NEVER

 apply voltage or current to the meter that exceeds the 

specified maximum: 

Input Protection Limits 

Function Maximum 

Input 

VAC 750V 

DC/AC 

V DC or V AC 

1000V DC/AC, 200Vrms on 200mV range 

mA DC 

200mA 250V fast acting fuse 

A DC 

20A 250V fast acting fuse(30 seconds max 
every 15 minutes) 

Ohms, Continuity 

250Vrms for 15sec max 

2. 

USE EXTREME CAUTION

 when working with high voltages. 

3. 

DO NOT

 measure voltage if the voltage on the "COM" input 

jack exceeds 1000V above earth ground. 

4. 

NEVER

 connect the meter leads across a voltage source 

while the function switch is in the current, resistance, or diode 
mode. Doing so can damage the meter. 

5. 

ALWAYS

 discharge filter capacitors in power supplies and 

disconnect the power when making resistance or diode tests. 

6. 

ALWAYS

 turn off the power and disconnect the test leads 

before opening the covers to replace the fuse or battery. 

7. 

NEVER

 operate the meter unless the back cover and the 

battery cover is in place and fastened securely. 

Содержание 411



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды