Extech Instruments 407790 Скачать руководство пользователя страница 8

Страница: 8 / 17

[ 1 / 3 OCT ] 01 / 07/ 27 14:26:39

31.5

500

125

L W

FAST

75.2 dB

100

Calibration

Use a standard acoustic calibrator such as the Extech 407744 or
407766. Acoustic calibration if often performed on a daily basis to
compensate for any possible changes in microphone sensitivity.

1. Configure the following switch settings.

Display: SLM (L

)

Time weighting: FAST

2. Insert the microphone carefully into the insertion hole of the

calibrator.

3. Turn on the calibrator and adjust its CAL potentiometer so

that the display matches the calibrator output.

4. Note that the 407790 is fully calibrated before shipment.

5. Recommended full recalibration cycle: 1 year.

Measurement Preparation

1. Battery loading: Remove the rear battery cover and insert four 1.5V ‘C’ size batteries.

Take care to observe battery polarity.

2. Battery replacement: When the battery voltage drops below operating voltage,
3. LBATT flashes on the display.

4. AC adaptor connection: Insert the adaptor in the DC 6V jack on the side panel.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Содержание 407790


















Результаты поиска

Содержание 407790

Отзывы:

Похожие инструкции для 407790

Бренды по названию

Популярные бренды

Extech Instruments 407790, Руководство пользователя

Результаты поиска

Содержание 407790

Отзывы:

Похожие инструкции для 407790

Бренды по названию

Популярные бренды