background image

Model 401036 Version 3.1   9/07 

Meter Description 

1. 2000 Count LCD includes LUX, Fc, low battery, MAX, H (hold), & x10 indicators 

2. ON/OFF key Turns the meter on or off 

3.  Max. Hold key When pressed, the LCD 

displays only the maximum reading 

4. Lux/Fc key Press to toggle the displayed 

unit of measure. The LCD shows the 
unit 

5. Light Sensor (Lens cover not shown) 

Collects light. Note that a tripod mount 
is located on the rear of the sensor  

6. Range key Press repeatedly to select 

desired range: 20, 200, 2,000, 20,000 

7.  Data Hold key Press to freeze the 

displayed measurement 

8. Record/Erase key Press momentarily to 

store one reading; Press and hold for 3 
seconds to activate the continuous 
recording mode. Press again to end 
recording 

9. RS-232 jack Stereo jack for PC to Meter 

connection cable 

10. Zero adjust Cover the sensor with 

supplied lens cap and adjust the zero 
pot for a 0.0 Fc/LUX display 

Note that the battery compartment, tilt stand, and hanging mount are located on the rear of 
the meter 

Spectral Sensitivity Curve 

                                                                                                     = Light Meter 

                                                                                                                   = V (

λ

)

 

Relative 

Sensitivity (%) 

 

 

 

 

 

                                                             Wavelength (nm)  

100 

 

80 

 

60 

 

40 

 

20 

400     450     500     550     600     650     700 

1

8

7

6

5

4

3

2

9

10

Содержание 401036







Отзывы: