1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Com-
puter and gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of your
computer. Make sure it is the right expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card.
Make sure the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer’s cover and the mounting screws.
HARDWARE INSTALLATION :
6
5
EX
EX
EX
-
-
-
41012 / 41212
41012 / 41212
41012 / 41212
English
English
English
EX
EX
EX
-
-
-
41012 / 41212
41012 / 41212
41012 / 41212
English
English
English
1
JUMPER
EINSTELLUNG & ANSCHLÜSSE
:
Die EX-41012 ist eine 32-Bit PCI Parallel Karte mit zwei Parallelen EPP/ECP Bi-
Direktionalen Ausgängen für den Anschluss von Peripheriegeräten mit Enhanced
Centronics Interface (z.B. Drucker, Scanner, Laufwerke usw.). Sie unterstützt den 32
und 64-Bit PCI bzw. PCI-X Bus mit 5 Volt und 3,3 Volt. Es ist nicht möglich die I/O
Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte vom
System (BIOS) und beim Installieren des Betriebssystems automatisch vorgenommen
werden. Die EX-41012 funktioniert nur mit Motherboards die Plug & Play Mode unter-
stützen, ansonsten wird sie nicht erkannt und kann nicht installiert werden. Die EX-
41212 ist eine LowProfile Karte mit einer maximalen Bauhöhe von 8cm.
BESCHREIBUNG & TECHNISCHE DATEN
:
AUFBAU
:
Kompatibilität:
PCI & PCI-X 3,3Volt & 5Volt bei 33Mhz
Betriebs Systeme:
DOS/WIN 9x/ME/NT4.0/2000/XP/Server2003/Vista/(Linux v. OS)
Anschlüsse:
2 x 25 Pin Sub-D Buchse
Lieferumfang:
EX-41012 bzw. 41212, Treiber CD, Anleitung, 25 Pin Kabel
Zertifikate:
CE
CE
CE
CE
/
FCC / RoHS / WEEE DE97424562
INSTALL A PERIPHERAL DEVICE:
Now you can install a Centronics parallel device to the EX-41012/41212.
Attention!!
If you want to connect old devices, it is possible that they wont work with
PCI or PCI-Express cards. In this case please connect the older device to the mother-
board and the newer device to the EX-41012 / 41212. If it is necessary to connect a old
device to the EX-41012 / 41212 please make sure that you use the latest driver and
firmware for the device. If you experience problems with installing such devices or you
are not sure that they will work. Please contact the manufacturer of the device for
further information!
Windows NT 4.0:
Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:).
Click at >
Start
< >
Run
< and enter
“D:\IO\NETMOS\98XX\WinNTMultiioDrivers.exe
"
then click
>OK<
. Windows NT will now start the setup program and install the driver.
Please Restart Windows NT after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click to >
Start<
>
Programs<
>
Administrative Tools[Common]<
>
Windows NT-
Diagnostics<
after you click to >
Resource<
>
IRQ<
. By this windows you can see >
10
NmSer 0 PCI
<. For the parallel port don’t have IRQ information. You click to >
I/O-
Port<
. Here you see two setting „
E400-E406 NmSer 0 PCI
“ and „
D800-D806 NmSer 0
PCI
“ for the serial ports and
„DC00-DC06 NmPar 0 PCI“
for the parallel port. The I/O
addresses can be change, that depends which system configuration you have. If you see
this information, the card is installed correctly.
LINUX:
There are no drivers available for Linux, but the card is supported by the most versions
of Linux. Because each individual distribution and kernel version of Linux is different,
sadly we cant provide a installation instruction. Please refer to the installation manual
for standard IO ports from your Linux version! In some newer versions the card will
even be installed automatically after starting Linux.
MS-DOS:
Copy the DOS driver file from the CD (
D:\IO\NETMOS\98XX\DOS\NmDosln.exe
) to the
root directory on your hard disk (C:\). Modify the “
AUTOEXEC.BAT
“ with the following line:
C:\NmDosln -a -r
After you reboot DOS , you can see the card with LPT2 and LPT3. The IRQ its set from
System-BIOS and can’t be changed.
DRIVER INSTALLATION :
DRIVER INSTALLATION :
Windows 9x/ME/2000/XP & Vista:
After starting Windows it recognizes a new
“PCI Controller“
and open the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path
"D:\IO\NETMOS\98XX"
and then the directory of your oper-
ating system
“WIN95“ “WIN98“ “WIN98“ “WINME“ “WIN2000“ “WINXP“
“WINXP_64“ “Vista32“ or “Vista64“
into the box for the Path/Source and click at
>next/continue<
. Now Windows search for the drivers in the specified directory. Follow
the hardware assistant and finish the installation. If Windows recognizes other new
devices repeat the above described steps.
Attention!
Restart Windows after installing.
CHECK THE INSTALLED DRIVER:
Click at
Start
<>
Run
< then enter
“compmgmt.msc“
and click at
>OK<
. In the windows
that open select
>Device Manager<.
Under
”Ports (COM and LPT)“
you should find
one or more new
”PCI Ports“
as sample
(LPT2).
If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example LPT3 to LPT 1, open the
>Device Man-
ager<
click at
>LPT3<, >Settings<
and then
>Advance<
. There you can change between
LPT1 to 2.
INSTALL A PERIPHERAL DEVICE:
Now you can install a Centronics parallel device to the EX-41012/41212.
Attention!!
If you want to connect old devices, it is possible that they wont work with
PCI or PCI-Express cards. In this case please connect the older device to the mother-
board and the newer device to the EX-41012 / 41212. If it is necessary to connect a old
device to the EX-41012 / 41212 please make sure that you use the latest driver and
firmware for the device. If you experience problems with installing such devices or you
are not sure that they will work. Please contact the manufacturer of the device for
further information!
Windows Server 2000/2003:
After starting Windows it recognizes a new
“PCI Controller“
and open the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path
"D:\IO\NETMOS\98XX"
and then the directory of your oper-
ating system for Server 2000:
“WIN2000“
and for Server 2003:
“WINXP“ or
“WINXP_64“
into the box for the Path/Source and click at
>next/continue<
. Now
Windows search for the drivers in the specified directory. Follow the hardware assistant
and finish the installation. If Windows recognizes other new devices repeat the above
described steps.
Attention!
Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at
Start
<>
Run
< then enter
“compmgmt.msc“
and click at
>OK<
. In the windows
that open select
>Device Manager<.
Under
„Ports (COM and LPT)“
you should find
one or more new
”PCI Ports“
as sample
(LPT2).
If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example LPT3 to LPT 1, open the
>Device Man-
ager<
click at
>LPT3<, >Settings<
and then
>Advance<
. There you can change between
LPT1 to 2.
Bedienungsanleitung
Bedienungsanleitung
Vers. 3.0 / 28.06.07
P1:
25 Pin Buchse
Parallel Ausgang
Bi-Direktional
Parallel Chip EPP/ECP
mit 32-Byte Buffer und
PCI-Bridge
Pin
Signal
Pin
Signal
Pin
Signal
1
STROBE
10 ACKNOWLEDGE 19
GROUND
2
DATA 0
11
BUSY
20
GROUND
3
DATA 1
12
PAPER EMPTY
21
GROUND
4
DATA 2
13
SELECT
22
GROUND
5
DATA 3
14
AUTO FEED
23
GROUND
6
DATA 4
15
ERROR
24
GROUND
7
DATA 5
16
INIT
25
GROUND
8
DATA 6
17
SELECT INPUT
9
DATA 7
18
GROUND
Parallel 25 Pin Buchse (P1):
DB 25F:
HARDWARE
INSTALLATION
:
Wenn Sie die Karte installieren, beachten Sie bitte die folgenden Installationshinweise.
Da es grosse Unterschiede bei Computern gibt, können wir Ihnen nur eine generelle
Anleitung zum Einbau geben. Bei Unklarheiten halten Sie sich bitte an die Bedienungs-
anleitung Ihres Computersystems.
P2
25 Pin Buchse
Parallel Ausgang
Bi-Direktional über
Anschlusskabel
