Exmark NAVIGATOR NV640KC Скачать руководство пользователя страница 40

Страница: 40 / 52

Troubleshooting

Problem

Possible Cause

Corrective Action

1. Engine load is excessive.

1. Reduce the ground speed.

2. Air cleaner is dirty.

2. Clean or replace the air cleaner element.

3. Oil level in the crankcase is low.

3. Add oil to the crankcase.

4. Cooling fins and air passages for the

engine are plugged.

4. Remove the obstructions from the cooling

fins and air passages.

5. Vent hole in the fuel cap is plugged.

5. Clean or replace the fuel cap.

6. Dirt in fuel filter.

6. Replace the fuel filter.

Engine loses power.

7. Dirt, water, or stale fuel is in the fuel

system.

7. Contact an Authorized Service Dealer.

1. Engine load is excessive.

1. Reduce the ground speed.

2. Oil level in the crankcase is low.

2. Add oil to the crankcase.

Engine overheats.

3. Cooling fins and air passages for the

engine are plugged.

3. Remove the obstructions from the cooling

fins and air passages.

1. Tracking needs adjustment.

1. Adjust the tracking.

2. Tire pressure in drive tires not correct.

2. Adjust tire pressure in the drive tires.

Mower pulls left or right (with levers fully
forward).

3. Reverse indicator and speed control

linkage need adjustment.

3. Adjust the reverse indicator and the speed

control linkage.

1. Bypass valve is not closed tight.

1. Tighten the bypass valve.

2. Drive or pump belt is worn, loose or

broken.

2. Change the belt.

3. Drive or pump belt is off a pulley.

3. Change the belt.

4. Broken or missing idler spring.

4. Replace the spring.

Machine does not drive.

5. Hydraulic fluid level is low or too hot.

5. Add hydraulic fluid to reservoir or let it

cool down.

1. Engine mounting bolts are loose.

1. Tighten the engine mounting bolts.

2. Loose engine pulley, idler pulley, or blade

pulley.

2. Tighten the appropriate pulley.

3. Engine pulley is damaged.

3. Contact an Authorized Service Dealer.

Abnormal vibration.

4. Belt is damaged.

4. Install new belt.

Содержание NAVIGATOR NV640KC





















































Результаты поиска

Содержание NAVIGATOR NV640KC

Отзывы:

Похожие инструкции для NAVIGATOR NV640KC

Бренды по названию

Популярные бренды

Exmark NAVIGATOR NV640KC, Руководство оператора

Результаты поиска

Содержание NAVIGATOR NV640KC

Отзывы:

Похожие инструкции для NAVIGATOR NV640KC

Бренды по названию

Популярные бренды