Exmark NAVIGATOR NV640KC Скачать руководство пользователя страница 16

Страница: 16 / 52

Specifications

•

PTO Engagement Lever: Engages drive to PTO
(mower deck) and blower.

•

Parking Brake Lever: Pull back to engage parking
brake.

Seat

•

Type: Standard seat with high back, foam padded
(internal suspension).

•

Mounting: Seat is hinged to tilt up for access to
hydraulic pumps and other components. The seat
is held in the tilted position with a link.

•

Armrests: None.

•

Seat Safety Switch: Internal to the bottom seat
cushion, non serviceable. Time delay module
incorporated into the Safety Interlock System
eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

•

Hydrostatic Pumps: Two Hydro Gear variable
displacement piston pumps.

•

Wheel Motors: Hydro Gear planetary reduction
motors.

•

Hydraulic Oil Type: Use Exmark Premium Hydro
oil.

•

Hydraulic Oil Capacity: 4.0 qt. (3.8 L)

•

Hydraulic Filter: Replaceable cartridge type.

– Summer use above 32°F (0°C):

P/N 109-0071: 25 microns, 10 psi bypass

– Winter use below 32°F (0°C):

P/N 1-523541: 40 microns, 18 psi bypass

•

Speeds:

– 0-7.0 mph (11.3 km/hr) forward.

– 0-5.5 mph (8.6 km/hr) reverse.

•

Drive wheel release valves allow machine to be
moved when engine is not running.

Tires & Wheels

Drive

Front
Caster

Rear Caster

Pneumatic
(Air-Filled)

Semi-
Pneumatic

Quantity

Tread

“Multi-Trac
C/S”

Smooth

Drive

Front
Caster

Rear Caster

Size

18 x
10.50-10

8 x 3.00-4

13 x 8.00-6

Ply Rating

Pressure

15 psi (103
kPa)

Cutting Deck

(Sold separately)

•

Model Numbers:

– CD42CD

– CD48CD

•

Cutting Width:

– 42 inch Deck: 42 inch (106.7 cm)

– 48 inch Deck: 48 inch (121.9 cm)

•

Discharge: Center

•

Blade Size: (2 ea.)

– w/42 inch Deck: 22.00 inches (55.9 cm)

– w/48 inch Deck: 25.00 inches (63.5 cm)

•

Deck Drive:

– Clutching belt on horizontal engine shaft.

Dual “A” section hexagon belt with spring
tensioned idler to jackshaft and blower.

– Heavy-duty cast iron, spiral bevel gearbox is

final drive to blades.

•

Deck:

Full floating deck is attached to out-front support
frame. Deck design allows for bagging or
mulching.

•

Deck Depth:

– 42 inch Deck: 4 5/8 inches (11.7 cm)

– 48 inch Deck: 4 5/8 inches (11.7 cm)

Dimensions

Overall Width:

Without Deck

42 inch Deck

48 inch Deck

42.6 inches (108.2
cm)

43.2 inches (109.7
cm)

49.2 inches (125.0
cm)

Содержание NAVIGATOR NV640KC





















































Результаты поиска

Содержание NAVIGATOR NV640KC

Отзывы:

Похожие инструкции для NAVIGATOR NV640KC

Бренды по названию

Популярные бренды

Exmark NAVIGATOR NV640KC, Руководство оператора

Результаты поиска

Содержание NAVIGATOR NV640KC

Отзывы:

Похожие инструкции для NAVIGATOR NV640KC

Бренды по названию

Популярные бренды