Exmark Lazer Z 52 Скачать руководство пользователя

Страница: 23 / 40

5.1.2 Idler Bushings:

Service Interval: 25 Hours.

Lubricate with 1-2 pumps of SAE No. 2 multi-purpose grease.

5.1.3 Bags:

Service Interval: Daily

Inspect the bags for wear, tears, or damage.

WARNING

POTENTIAL HAZARD

♦

Under normal use the bag will deteriorate and wear.

Objects could exit a worn bag at high speeds.

WHAT CAN HAPPEN

♦

Thrown objects can cause serious injury or kill you or

bystanders.

HOW TO AVOID THE HAZARD

♦

Check bag frequently for tears and holes. Replace

worn bag.

5.1.4 Belts.

Service Interval: 50 Hours.

For 52” units only -

Inspect the belt position on the idler arm.

The idler arm may become bent during use or transport. A bent idler arm could
cause the belt to jump off of the idler and be damaged.
1) Make sure the belt cover is installed and run the blower for one to two minutes

Shut off the deck drive, stop engine and wait for all moving parts to stop.
Remove key.

Remove the belt cover and check to make sure that the belt is

riding near the center of the flat idler on the idler arm.

3) If the belt is not riding near the center of the idler, remove the blower, and bend

the idler arm slightly.

4) Reinstall the blower and belt cover and repeat steps 1-3 until the belt is

positioned near the center of the idler.

All Units

- Inspect the belt for damage or wear. Replace belt with one of the

following.

52” deck – PN 1-653438
60” deck – PN 103-0866
72” deck – PN 103-0867

5.1.5 Clean muffler and rear frame area:

Service Interval: Daily

WARNING

POTENTIAL HAZARD

♦

Operating engine parts, especially the muffler, become

extremely hot.

WHAT CAN HAPPEN

♦

Severe burns can occur on contact.

♦

Debris, such as leaves, grass, brush, etc. can catch fire.

HOW TO AVOID THE HAZARD

♦

Allow engine parts, especially the muffler, to cool before

touching.

♦

Remove accumulated debris from muffler and engine area.

♦

Install and maintain in working order a spark arrester before

using equipment on forest-covered, grass-covered, brush-
covered unimproved land.

Содержание Lazer Z 52









































Результаты поиска

Содержание Lazer Z 52

Отзывы:

Похожие инструкции для Lazer Z 52

Бренды по названию

Популярные бренды

Exmark Lazer Z 52, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Lazer Z 52

Отзывы:

Похожие инструкции для Lazer Z 52

Бренды по названию

Популярные бренды