Self-Test/Self-Diagnostics (G2)
I M P O R T A N T:
Once all emergency lamps have been connected to the unit equipment, apply normal AC power and
FKDUJHIRUKRXUV
Following installation and after AC power has been supplied, charge for 48 hours, then press and hold the test button until
the LED indicator turns orange. This calibrates the unit equipment for the proper load.
Operation
The purpose of this option is to provide Self-testing and Self-diagnostic capabilities to the emergency unit. At
predetermined intervals, the emergency unit will automatically switch into battery mode. Refer to the
Self-Test Feature
section below for timing details. The emergency unit will also perform various Self-diagnostic tests to determine if there
are any faults. Visual signaling will alert maintenance personnel to a fault of the emergency unit electronics, battery,
DQGRUEDWWHU\FKDUJHU7KHFLUFXLWU\FRQWLQXRXVO\PRQLWRUVWKHRSHUDWLQJFRQGLWLRQRIWKHHPHUJHQF\XQLWDQGEDWWHU\
FKDUJLQJFLUFXLWEDWWHU\VXSSO\YROWDJH5HIHUWRWKH
LED Indicator
section below for fault reporting details.
Self-Test Feature
• The emergency unit will automatically switch to battery mode every
PRQWKIRUDSHULRGRIPLQXWHV
• The emergency unit will automatically switch to battery mode every
PRQWKVIRUDSHULRGRIPLQXWHV
LED Indicator
The LED indicator of the emergency unit will display a visual signal indicating the status of the unit. Refer to the table
below for LED indication conditions:
Test Button Features
MANUAL TEST – Pressing the test button will switch the unit into battery mode for a set amount of time. The desired
length of the test is determined by the length of time that the test button is pressed.
3UHVVLQJWKHWHVWEXWWRQRQFHZLOOVZLWFKWKHXQLWLQWREDWWHU\PRGHIRUDSHULRGRIVHFRQGV
• Pressing and holding the test button until the LED indicator turns orange will switch the unit into battery mode for a
SHULRGRIPLQXWHV
3UHVVLQJDQGKROGLQJWKHWHVWEXWWRQXQWLOWKH/('LQGLFDWRUIODVKHVUHGJUHHQZLOOVZLWFKWKHXQLWLQWREDWWHU\PRGH
IRUDSHULRGRIPLQXWHV
Pressing the test button once while the unit is MANUAL TEST mode will cancel the manual test and return the unit to
normal AC power.
5(6(7±3UHVVLQJWKHWHVWEXWWRQWLPHVZLOOUHVHWWKHUHG³81,7$/(57´/(',IPXOWLSOHIDXOWVDUHSUHVHQWLWPD\EH
QHFHVVDU\WRUHSHDWWKLVSURFHGXUHIRUHDFKUHPDLQLQJIDXOWLQGLFDWHGE\WKH³81,7$/(57´/('
Use in accordance with local building codes.
LED Indication
Steady
Pulse
Steady
Pulse
Steady
Pulse
LED Color
LED Color
Green
Green
Red
Red
Orange
Orange
5HG*UHHQ
Unit Condition
Float Charge
Hi-Rate Charge
/RZ%DWW9ROWDJH
Emer Lamp Failure
No AC Power
Charge Failure
0LQXWH7HVW
%DWW'LVFRQQHFWHG
0LQXWH7HVW
Comment
%DWW)XOO\&KDUJHG
%DLJK5DWH&KDUJH
5HSODFH%DWWHU\
Check AC Connection
Replace Transformer
0LQ7HVW(YHU\0RQWK
&KHFN%DWW&RQQHFWLRQV
0LQ7HVW(YHU\0RQWKV
Replace Damaged or
Missing Lamps
CP-EMW Series
Installation Instructions
R
(9
4
ZZZEDUURQOWJFRP
