background image

18

19

Cleaning Your Alarm

Over time dust might collect inside your alarm, altering its performance.  If this 

occurs, the unit can false alarm or the WARNING icon will flash and the horn will 

chirp every 30 seconds.  To clean the alarm perform the following:

Remove the alarm from its bracket.  If the 

smoke alarm is wired to the AC power lines, 

the wire harness must be disconnected.  

Gently vacuum all the outside surfaces care-

fully or wipe with a clean cloth.

Locate the black smoke chamber on the back 

surface of the smoke alarm.

If the WARNING icon flashing persists, 

return the alarm to the manufacturer.

Twist the chamber counter-clockwise to 

remove.

Carefully clean both the chamber 

and

 the 

empty alarm cavity with compressed air.

With the AC wire harness reconnected (if 

AC alarm type), re-install on the ceiling/wall 

bracket with a clockwise twist.  

Re-install the smoke chamber into the cavity 

with a clockwise rotation.  Align the dots on 

chamber and housing to ensure a proper fit.

Press and release the Test button on the front 

face to verify the alarm is still functioning 

properly.  

Black

Line (Hot)

Neutral 

Signal

White

Red

Black

Line (Hot)

Neutral 

Signal

White

Red

How to Wire and Mount the AC Powered Alarm

When installing an AC powered alarm (Model EX20AC SMK), the mounting location is 

determined by the position of the electrical box that will power the alarm.  

Electrical 

power to the box must be disconnected prior to alarm connection and 

installation!

With the AC power turned off

, connect 

the wire harness provided with the alarm.

Connect the black wire of the harness to 

the black wire(s) in the electrical box.

Typical 

Circuit

End of 

Line 

Circuit

Align and attach the mounting bracket 

with the two screws from the electrical 

box. Pass the wire harness through the 

center of the bracket.

Plug the wire harness into the back of the 

alarm.

Press and twist the alarm clockwise into 

place (see Step 4 of previous section).

Reconnect power to the AC lines of the 

smoke alarm circuit.  The POWER icon will 

glow continuously.

Using the supplied orange wire nut, cap 

the red wire(s) (not used) and push it 

back inside the electrical box.

Connect the white wire of the harness to 

the white wire(s) in the electrical box.

Smoke Manual with FCC and IC Statement.indd   Sec1:18-Sec1:19

8/5/2013   11:59:31 AM

Содержание EX20 SMK














Отзывы: