EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 271 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

261

MAC/IP/UDP



TTL

(IPv4) or

HOP Limit TTL

(IPv6) sets the Time To Live value:

255

(default is

128



Flow Label

(IPv6) is a number used to identify a series of related

packets from a source to a destination:

(default) to

1048575



IP TOS/DS

(IPv4) or

Traffic Class (TOS/DS)

- (IPv6) allows entering

either an hexadecimal value,

(default) to

, or tap on the

TOS/DS

Config

button to set each TOS or DS parameter individually. Changing

the

IP TOS/DS

value will affect the

TOS/DS Config

settings and vice

versa.



TOS/DS Config

button allows setting the Type of Service or the

Differentiated Service parameters.

TOS/DS



TOS/DS

allows selecting either Type Of Service (TOS) or

Differentiated Services (DS).



Binary/Hex

allows displaying, once this pop-up is closed, the IP

TOS/DOS value either in binary or hexadecimal.

Type Of Service

(available when

TOS

is selected).



Precedence

value:

000 (Routine)

(Default)

001 (Priority)
010 (Immediate)
011 (Flash)
100 (Flash Override)
101 (CRITIC/ECP)
110 (Internet Control)
111 (Network Control)



Delay

allows the selection of the delay level:

Normal

(default) or

Low



Throughput

allows the selection of the throughput level:

Normal

(default) or

High

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды