EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 86 / 803

background image

Test Setup - Test Applications

74

88000 Series

Cable Test

Cable Test

The cable test application is used to diagnose un-shielded twisted pairs
(UTP) cables (up to Category 6e/Class E).

Cable test can be performed everywhere in the network where an
electrical 10/100/1000 Mbit/s Ethernet interface is available for testing. Only
the pairs used by the Ethernet signal will be tested. For 10 Base-T, and
100 Base-TX, pair 2 and 3 will be tested; for 1000 Base-T, all pairs will be
tested. However, if the Ethernet signal is unknown, all four pairs will be
tested.

Even if a link up is not required when testing with a far end equipment, it is
preferable to have the far end equipment powered up to maximize the
cable test results.

Supported Ethernet cable categories are: Category 3/Class C, Category 4,
Category 5, Category 5e/Class D, and Category 6e/Class E.

Note:

Cable test result is reliable for cable length of 10 meters to 120 meters
(32.81 feet to 393.7 feet).



Typical Cable Test applications:



Supported Interfaces/Rates: 10M to 1000M Electrical.

Testing Unit

Far end equipment

EXFO Module

UTP cable

Testing Unit

Unplugged cable

EXFO Module

UTP cable

«
...
84
85
86
87
88
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: Dantherm Страницы: 96

Бренд: Yudian Страницы: 26

Бренд: K'Nex Education Страницы: 56

Бренд: Panamax Страницы: 16

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренд: Saluki Страницы: 13

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: Partizan Страницы: 7

Бренд: Klimaire Страницы: 5

Бренд: Desoutter Страницы: 74

Бренд: jablotron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды