EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 497 / 803

background image

Test Results

Power Blazer

485

Summary (EtherSAM)

Summary (EtherSAM)

From the

Test

menu, tap

Results

, and the

Summary

tab.

Note:

For

Dual Test Set

, only Start Time is displayed on the remote module.



Service Configuration/Performance Test Status

indicates the actual

test status as follows:



Start Time

indicates the date and time the test was started. The date

and time is reset every time the test is restarted.



Remote unit in use and locked for Dual Test Set

indicates that this

module is used for

Dual Test Set

as the remote module.

Test Status

Description

“--”

Test has not started.

Disabled

Test/subtests is/are disabled.

Running

Test/subtest is currently running.

Data Transfer

Test/subtest is running but no test traffic is being transmitted.

Completed

, <Verdict> Test/subtest has completed with the test pass/fail verdict. A

fail verdict is declared when a

Link Down

or

LOS

is detected,

or when any SLA parameter fails.

Aborted

,

<

reason

>

Test/subtest has been aborted either manually (Stop) or
automatically from an alarm and the reason why the test has
been aborted is also displayed as follows:

Link down alarm

,

LOS alarm

,

Timeout during execution

,

DTS connection failed

,

Loss of remote connection (DTS)

,

LOPPS-L Alarm

a

,

LOPPS-R Alarm

LOPPS-L / LOPPS-R Alarm

,

Unresolved addresses

,

No test enabled

,

Invalid Burst Configuration

,

CIR disabled for all services

,

Excessive Refill Time

b

,

Stopped

,

NAT detection failed

,

Missing DTS-NAT SW option

a.

Available for

Dual Test Set

in

One-Way Latency

measurement mode.

b.

An excessive refill occurs when the pre-burst and/or post-burst duration last for

more than 2 seconds.

«
...
495
496
497
498
499
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: ZIMO Страницы: 38

Бренд: FAAC Страницы: 32

Бренд: UCS Страницы: 4

Бренд: Samson Страницы: 73

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: U-Prox Страницы: 3

Бренд: Parker Страницы: 42

Бренд: Case IH Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды