EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 300 / 803

background image

Test Setup - Test Configurator, Timer, and System

288

88000 Series

Signal (Transport)



Min RX Power (dBm)

1

indicates, when supported, the minimum

received power level of the optical lane/laser in dBm.



Max RX Power (dBm)

indicates, when supported, the maximum

received power level of the optical lane/laser in dBm.



Laser ON/OFF

button is used for parallel interfaces to activate the laser

control per optical lane or for all lanes.

Optical lane numbers are from

0

to

3

or

0

to

7

depending on the

selected interface/rate.



All Lanes

check box, when selected, applies the change(s) to all

optical lanes at once.



Optical Lane

indicates the optical lane numbers and

All

which

represents the setting for all optical lanes when the

All Lanes

check box is selected.



Laser

check box, when selected, indicates that the corresponding

optical laser lane is activated and emitting an optical laser signal.



Lasers OFF at Start-Up

check box when selected automatically turns

OFF the laser for serial interfaces or all lasers for parallel interfaces
when starting the Power Blazer or when switching from one test
application to another. However the laser remains ON, on a remote
module receiving a request for a DTS connection or a loopback
command. This check box is cleared by default.



Power Range (dBm

) indicates the transceiver operational RX power

range.

1. Displayed for each optical lane for parallel interfaces.

«
...
298
299
300
301
302
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Panasonic Страницы: 45

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Parker Страницы: 28

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Therma-Stor Страницы: 20

Level-Trac LT-310

Бренд: QTS Страницы: 12

Бренд: DEUTSCHMANN AUTOMATION Страницы: 30

total control MRX-10

Бренд: Universal Remote Control Страницы: 16

Бренд: RTI Страницы: 2

SAMSUNG URC-4910

Бренд: One for All Страницы: 76

EZ Power Remote

Бренд: Pogo Страницы: 1

Бренд: Badger Meter Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды