manualshive.com logo in svg

EXFO bv10, Руководство пользователя, Страница: 79 / 116

Поделиться
Скачать
EXFO bv10 Скачать руководство пользователя страница 79

BV10-100 and BV10-1000

73

8

Test Applications 

The BV10 supports the following test applications: 

Smart Loopback supports wire-speed operation with TWAMP, UDP, and 
OAM handlers. 

In addition to the test applications listed above, the BV10 responds to ARP 
and Ping packets targeted to the unit (not wire-speed). 

The BV10 provides counters for the number of packets processed by each 
test and each Ethernet OAM message type. Refer to 

show statistics

 on 

page 49 for more information. The test application counters are 
automatically reset when there is: 

Link-up event on the Test port. 

Any Test port configuration change. 

Test control changes from disabled to enabled (applies to TWAMP 
Light, UDP Echo, and Ethernet OAM handling). 

The Smart Loopback Operational Status changes from Not Operational 
to Operational (applies to Smart Loopback test). 

The Smart Loopback mode is changed (applies to Smart Loopback 
test). 

All test application counters can be manually reset by entering the 

clear 

statistics

 command. Refer to 

clear statistics

 on page 50 for more information. 

Note:

All tests at the exception of Ping are disabled during software upgrades on 
the Test port. 

Test Application

Page

Smart Loopback Test

74

Ping Test

76

TWAMP Light Responder Test

77

UDP Echo Responder Test

78

Ethernet OAM Handling Test

79

Содержание bv10





















































































































Отзывы:

Нет отзывов