manualshive.com logo in svg

EXFO bv10, Руководство пользователя, Страница: 85 / 116

Поделиться
Скачать
EXFO bv10 Скачать руководство пользователя страница 85

Test Applications

BV10-100 and BV10-1000

79

Ethernet OAM Handling Test

Ethernet OAM Handling Test 

The Ethernet OAM handling test listens for Ethernet OAM messages in both 
Ethernet II and 802.3 LLC/SNAP frame format and responds in the received 
format. 

No VLAN ID checking is done. The Ethernet OAM feature responds with 
VLAN parameters of the received packet. In addition, no MEG-level 
discrimination is done, which allows the BV10 to operate in promiscuous 
mode (the unit operates as a MEP at multiple levels without any MEG-level 
configuration).

Ethernet OAM handling can be globally enabled (default) or disabled. Refer 
to 

eth-oam enable|disable

 on page 72 for more information. 

The BV10 listens for and responds to the following Ethernet OAM 
messages:

Loopback 

The BV10 responds to Unicast OAM Loopback messages when all of 
the following criteria are met: 

Global Ethernet OAM handling is enabled (default).

Destination MAC address equals the MAC address of the Test port.

EtherType is 0x8902.

OpCode is 3 (LBM).

Содержание bv10





















































































































Отзывы:

Нет отзывов