EXFO bv10 Скачать руководство пользователя страница 83

Страница: 83 / 116

Test Applications

BV10-100 and BV10-1000

TWAMP Light Responder Test

TWAMP Light Responder Test

The TWAMP Light Responder test listens for TWAMP Light messages on the
specified UDP port and responds with a reflected packet when all of the
following criteria are met:



TWAMP Responder control is enabled (default).



Destination MAC address equals the MAC address of the Test port.



VLAN ID equals the VLAN ID of the Test port (if configured).



Destination IP address equals the IP address of the Test port.



Protocol equals UDP (17).



UDP destination port equals the configured TWAMP Listening UDP
port.

The TWAMP Light Responder test supports wire-speed operation.
Unauthenticated mode is assumed.

The TWAMP Light Responder test can be enabled (default) or disabled.
Refer to

twamp enable|disable

on page 71 for more information.

The UDP Listening port (default is 9495) is specified with the

twamp udp-port

command. Refer to

twamp udp-port value

on page 71 for more

information.

Содержание bv10





















































































































Результаты поиска

Содержание bv10

Отзывы:

EXFO bv10, Руководство пользователя, Страница: 83 / 116

Результаты поиска

Содержание bv10

Отзывы: