EXFO AXS-200/635 Скачать руководство пользователя страница 241

Страница: 241 / 267

Running a VoIP Test

Copper, VDSL2, ADSL2+, and IP Triple-Play Test Set

233

Reading Results

HPNA Statistics

The

HPNA

Statistics

tab allows you to view counter statistics of the

selected HPNA device.

Select Device

lists all the MAC

addresses of the detected HPNA
devices on the network.

Tx Packets

is the number of

packets sent.

Rx Packets

is the number of

packets received.

Tx Bytes

is the count of bytes sent.

Rx Bytes

is the count of bytes received.

Rx CRC Packets

is a count of cyclical redundancy check (CRC) errors

received.

Tx Packets Dropped

is the number of outgoing packets dropped.

Rx Packets Dropped

is the number of incoming packets dropped.

To select a MAC address:
1.

Press

to open the list.

In the list, press the up/down arrows to select the MAC address of the
desired device.

Press

to confirm the selection and view the results.

Содержание AXS-200/635












































































































































































































































































Результаты поиска

Содержание AXS-200/635

Отзывы:

Похожие инструкции для AXS-200/635

Бренды по названию

Популярные бренды

EXFO AXS-200/635, Руководство пользователя

Результаты поиска

Содержание AXS-200/635

Отзывы:

Похожие инструкции для AXS-200/635

Бренды по названию

Популярные бренды