EXELAIR EX5005KIT страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 29

background image

50-PIECE AIR TOOL KIT

C2

B2

D2

3/8" AIR RATCHET WRENCH

C2

B2

D2

28

1. How to install/tighten threaded fasteners.

Turn the F/R knob (C2) counterclockwise to “F”

position (F=Forward or Tighten). Press the

trigger (D2). The tool anvil (B2) runs clockwise.

(See Figure 28)

2. How to remove/loosen threaded fasteners.

Turn the F/R knob (C2) clockwise to “R” position

(R=Reverse or Loosen). Press the trigger (D2).

The tool anvil (B2) runs counterclockwise.

(See Figure 29)

29

30

H2

E2

G2

NOTE:

This tool features a power

regulator valve. Rotate the air regulator

(E2) until desired output is achieved. The

settings 1, 2, 3, 4 are only for reference

and do not denote a specific power

output. “Setting 1” (one-line symbol) is

the least amount of power while

“Setting 4” (four-line symbol) is the most

amount of power. Rotate the air

regulator (E2) until the desired setting is

lined up with the small steel ball (H2) on

air inlet (G2). (See Figure 30)

20

«
...
19
20
21
22
23
...
»

Содержание EX5005KIT






























Отзывы:

Нет отзывов

Похожие инструкции для EX5005KIT

Бренд: SAC Страницы: 80

Бренд: Jarvis Страницы: 12

Бренд: Jet Страницы: 20

Бренд: Jet Страницы: 28

Бренд: jbc Страницы: 12

Бренд: Chauvin Arnoux Страницы: 33

Бренд: U.S. General Страницы: 10

Бренд: Ingersoll-Rand Страницы: 24

Бренд: Park Tool Страницы: 2

Бренд: Yost Vises Страницы: 5

Бренд: Draper Страницы: 12

Бренд: Urrea Страницы: 12

Бренд: Velleman Страницы: 45

Бренд: REED Страницы: 2

Бренд: RASOR Страницы: 15

Бренд: Topeak Страницы: 2

Бренд: Scell-it Страницы: 20

Бренд: Astro Tool Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды