eXact PipeCut 220 INOX Series, Руководство по эксплуатации

Страница: 10 / 20

Safety English
9
Lower guard function
a) Check the lower guard for proper closing before
each use. Do not operate the saw if the lower guard
does not move freely and close instantly. Never
clamp or tie the lower guard into the open position.
If the saw is accidentally dropped, the lower guard may
be bent. Raise the lower guard with the retracting
handle and make sure it moves freely and does not
touch the blade or any other part, in all angles and
depths of cut.
b) Check the operation of the lower guard spring. If
the guard and the spring are not operating
properly, they must be serviced before use.
Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
c) The lower guard may be retracted manually only
for special cuts such as "plunge cuts" and
"compound cuts". Raise the lower guard by the
retracting handle and as soon as the blade enters
the material, the lower guard must be released.
For
all other sawing, the lower guard should operate
automatically.
d) Always observe that the lower guard is covering
the blade before placing the saw down on bench or
floor.
An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
The pipe saw must never be used in the
following cases:
There is water or another liquid, explosive gases, or
poisonous chemicals inside the pipe to be cut.
The power switch is faulty.
The power cable is faulty.
The blade is bent.
The blade is dull or in poor condition.
The plastic components are cracked or have parts
missing.
The gripper unit is not properly tightened around the
pipe or if it is warped.
The blade guard cover or moving blade guard has
been damaged or removed from the machine.
The locking mechanisms do not work properly
(UNLOCK - SWITCH).
The pipe saw has become wet.
When you use the saw, the following factors
shall be considered:
Support the pipes to be cut properly so that the
blade is not clamped between the ends of the pipes.
Support the pipe to cut securely. Pipe supports are
more reliable for holding the pipe than bare hands.
Make sure that the pipe to be cut is empty. Take
care that no-one will put anything inside the pipe
during the operation.
Make sure that the diameter and thickness of the
blade is suitable for the saw and that the blade is
suitable for rotational speed selected
Do not use damaged or faulty blades or blade
flanges. Blade flanges and nuts are custom made
for this tool to ensure optimum operating
performance and safety.
Never use axial friction force to stop the blade, let it
stop freely.
Check the parts of the blade protection, never
operate the tool if blade covers are not in place.
Never apply excessive force when using the
pipecut.
Never use the pipecut to lift the pipe when fixed on
the pipe.
Avoid excessive load on the electric motor.
Always wear a dust mask if cutting materials that
produce dust, for example cast iron with Diamond
blade.
Always follow safety and operation manual and
applicable regulations.
Intended Use
PipeCut 220 INOX Series
PipeCut 220 INOX Series pipe saw is intended for use
as a pipe fitter’s tool at the job site.
PipeCut 220 INOX Series can only be used to cut
round pipes, with a diameter of
20mm – 220mm (0.8"–8")
PipeCut 220 INOX Series pipe saw is designed to cut
stainless and acid proof pipe materials. It can be used
to cut other normal pipe materials, such as steel,
cast/ductile iron, copper, aluminum and plastic. When
cutting different materials, always use appropriate
blade.
Maximum wall thicknesses:
Stainless steel 12.5 mm (0.5")
PipeCut 220 INOX Series pipe saw is not intended for
use in industrial production.
Use only blades with the diameter stated in technical
data.
Do not use any abrasive wheels.
Do not use any blade with lower speed marking than
no-load speed marked on the power tool.
Use pipe holders to support the pipe being cut.