EWM Picotig 190 AC/DC 5P TG Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 62

background image

Design and function

TIG welding

099-000151-EW501

18.01.2013

25

5.6.2

Torch connection options and pin assignments

Figure 5-4

5.6.3

Shielding gas supply (shielding gas cylinder for welding machine)

WARNING

Incorrect handling of shielding gas cylinders!
Incorrect handling of shielding gas cylinders can result in serious and even fatal injury.
• Observe the instructions from the gas manufacturer and in any relevant regulations

concerning the use of compressed air!

• Place shielding gas cylinders in the holders provided for them and secure with fixing

devices.

• Avoid heating the shielding gas cylinder!

CAUTION

Faults in the shielding gas supply.
An unhindered shielding gas supply from the shielding gas cylinder to the welding
torch is a fundamental requirement for optimum welding results. In addition, a blocked
shielding gas supply may result in the welding torch being destroyed.
• Always re-fit the yellow protective cap when not using the shielding gas connection.
• All shielding gas connections must be gas tight.

NOTE

Before connecting the pressure regulator to the gas cylinder, open the cylinder valve
briefly to expel any dirt.

«
...
23
24
25
26
27
...
»

Содержание Picotig 190 AC/DC 5P TG































































Отзывы:

Нет отзывов

Похожие инструкции для Picotig 190 AC/DC 5P TG

Бренд: Eco Страницы: 2

Бренд: D+H Страницы: 4

Бренд: D+H Страницы: 12

Бренд: NewArc Страницы: 12

Masterweld 204T

Бренд: AES Страницы: 31

Бренд: Ewellix Страницы: 18

Бренд: VENCO Страницы: 21

EAGLE GRIP EG4MDC2-F

Бренд: Easy Lift Equipment Страницы: 17

Бренд: Subpac Страницы: 15

Бренд: ESAB Страницы: 20

Бренд: Hoshizaki Страницы: 10

Бренд: SICK Страницы: 112

Бренд: Everlast Страницы: 30

Бренд: TIP TEMPerature Products Страницы: 7

Бренд: LIFTINGITALIA Страницы: 24

Бренд: zika Страницы: 21

Party Rocker Express

Бренд: ION Страницы: 5

Бренд: BST Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды