EWM Expert XQ 2.0 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 92

background image

Quick overview

Machine display

16

099-00L105-EW501

07.06.2019

4.3.3.1 Basic settings for operation with two wire feeders (P10)

The setting is available/required in the following cases only:
• the control is integrated in the wire feeder
• the control is integrated in the power source (compact design)

Menu item/parameter

Value

Comment

DVX (single)

0

DVX-Unit 1 (master)

1

DVX-Unit 2 (slave)

2

With single unit operation (P10 = 0) a second wire feeder may not be connected!

• Remove any connections to the second wire feeder

With double unit operation (P10 = 1 or 2) both wire feeders have to be connected and be set up for

this operation at the control with different configurations.

• Configure one wire feeder as master (P10 = 1)
• Configure the other wire feeder as slave (P10 = 2)

Access control

If one of the wire feeders in the welding system is equipped with an access control key switch, it has to be

configured as master (P10 = 1). With double unit operation, if more than one wire feeder is equipped with

an access control key switch, either one can be configured as master. The wire feeder configured as

master is active as soon as the welding machine has been switching on. There are no other functional dif-

ferences between the wire feeders.

4.3.3.2 Change system language

During the start process the user can select or change the system language at the machine control.
• Switch the machine off and on again.
• Press the context-dependent push-button [D] during the start phase (the word WELDING 4.0 is dis-

played).

• Select the required language by turning the control button.
• Confirm the selected language by pressing the control button (the user can exit the menu by pressing

the context-dependent push-button [A] without making any changes).

Figure 4-5

«
...
14
15
16
17
18
...
»

Содержание Expert XQ 2.0





























































































Отзывы:

Нет отзывов

Похожие инструкции для Expert XQ 2.0

Бренд: K&K Страницы: 6

Бренд: ZIMO Страницы: 38

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: IDK Страницы: 96

M16/RM N.C. DN 65 EEX

Бренд: Madas Страницы: 44

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды