EWM drive 4 Basic MMA страница 12 Скачать руководство пользователя

Страница: 12 / 56

Safety instructions

Transport and installation

099-005401-EW501

17.06.2014

2.4.1

Ambient conditions

CAUTION

Installation site!
The machine must not be operated in the open air and must only be set up and
operated on a suitable, stable and level base!

• The operator must ensure that the ground is non-slip and level, and provide sufficient

lighting for the place of work.

• Safe operation of the machine must be guaranteed at all times.

CAUTION

Equipment damage due to dirt accumulation!
Unusually high quantities of dust, acid, corrosive gases or substances may damage the
equipment.

• Avoid high volumes of smoke, vapour, oil vapour and grinding dust!
• Avoid ambient air containing salt (sea air)!

Non-permissible ambient conditions!
Insufficient ventilation results in a reduction in performance and equipment damage.

•  Observe the ambient conditions!
•  Keep the cooling air inlet and outlet clear!
•  Observe the minimum distance of 0.5 m from obstacles!

2.4.1.1

In operation

Temperature range of the ambient air:

• -25 °C to +40 °C

Relative air humidity:

• Up to 50% at 40 °C
• Up to 90% at 20 °C

2.4.1.2

Transport and storage

Storage in an enclosed space, temperature range of the ambient air:

• -30 °C to +70 °C

Relative air humidity

• Up to 90% at 20 °C

Содержание drive 4 Basic MMA

























































Результаты поиска

Содержание drive 4 Basic MMA

Отзывы:

Похожие инструкции для drive 4 Basic MMA

Бренды по названию

Популярные бренды

EWM drive 4 Basic MMA, Руководство по эксплуатации

Результаты поиска

Содержание drive 4 Basic MMA

Отзывы:

Похожие инструкции для drive 4 Basic MMA

Бренды по названию

Популярные бренды