www.evolutionbuild.com
6
www.evolutionbuild.com
7
Multipurpose Blade Cuts Steel, Aluminium & Wood
Diameter
Speed
Bore
Kerf
Teeth
185mm
3500min
-1
20mm
2mm
20
Diamond Blade Cuts Stone, Paving & Brick
Diameter
Speed
Bore
Kerf
Rim
185mm
8000min
-1
20mm
2.5m
Segmented
Notice: Normal wear and tear and damage caused by misuse
is NOT covered under the 12 month guarantee.
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling center and disposed of in an
environmentally safe way.
Recyclable Materials Analysis List
Material
Weight (Kg)
Percentage (%)
Aluminum
1.1
21.10
Cast Iron
0
0.0
Iron Plate
3.3
63.40
Plastics
0.7
13.40
Others
0.1
1.90
Total
5.20
99.80
Major Packaging Materials
Material
Weight (Kg)
Carton
1.16
Polystyrene
0.00
Plastic
3.43
Polypropylene
0.001
Others
0
Total
4.59
Mounting / Removing TCT Saw Blades
Remove the chip collection cover from the machine by
undoing the two knurled knobs on the back. Using the
supplied Allen Wrench, undo the M8 bolt that secures the
blade and remove the blade flange. Note: Use spindle lock.
Replace blade, making sure that the arrow for the direction
of rotation of the blade matches that of the machine then
tighten the M8 bolt with the flange in the correct position.
Note: Check that the spindle lock is fully released by manually
rotating the blade before use.
Adjustment Of The Cutting Depth
Release the handle to adjust to the required cutting depth.
Ensure that the blade protrudes a maximum of 5/8” (4mm)
through the material being cut. Tighten the handle fully to
lock in position.
Adjustment Of The Cutting Angle
Release locking handle and adjust to the required cutting
angle by lining up the mark with the imprinted scale. Tighten
handle fully to lock in position. Note: There are certain
compound cuts on which it may be necessary to manually
retract the guard to allow the blade to enter into and / or
through the cut.
Line Of Cut Guide Slots
Guide slots are provided at the front of the saw base. One
slot is used to follow a line when making a 90° cut. The other
slot is used to follow a line when making a 45° cut.
Operating Advice
Always clamp the work piece on a rigid support such as a
bench or saw horses where possible. This tool is equipped
with a safety start feature - to start the tool, you must first
push in the switch on the side of the handle with your
thumb - you can then depress the main trigger switch to
power the motor. Do not force the tool - let the speed of
the saw blade do the work. Cutting performance will not
improve by applying more pressure on the tool and blade
life will be reduced. When using the parallel guide, ensure
that it is parallel with the blade and not the base of the tool,
as otherwise the blade and motor could become damaged.
To set the guide, loosen the retaining screw, and slide it up
snugly against the side of the work piece. Retighten the
screw to secure it in the desired position. Place front edge of
saw squarely on work before starting motor. When starting
a cut, sight the cutting line with the line of cut guide taking
care to introduce the blade to the material slowly, so as not to
damage its teeth. Use both hands to move the saw forward
through the work piece. If the tool overload protection device
activates – allow the motor to cool and then press the reset
button to continue operation.
Chip Collection
This tool is provided with a chip collector compartment.
When the chips accumulate up to the see-through window,
remove the cover, clean out the cover, then replace it, and
tighten the knobs. Notice: The metal chips inside the cover
may be very hot and sharp - do not touch with bare hands.
Dust Extraction
To allow the fitting of a dust extractor pipe, remove the small
black cover located at the top left of the chip collection cover.
Replace the cover when a dust extractor is not in use.
Maintenance & Troubleshooting
Keep tool and carry bag clean and free from chips. Avoid using
cleaning products, which include benzene, trichloroethelene,
chloride, and ammonia as these can damage plastic parts.
In case of electrical or mechanical malfunction, immediately
switch off the tool and disconnect the battery. For all other
service please contact our Technical Helpline.
Lubrication
Your machine is lubricated at the factory with sufficient lubricant
to last for approximately 72 hours of operation. To add lubricant,
it is necessary to dismantle the tool. Please contact our
Technical Helpline for information regarding this operation.
EVOLUTION BRAND BLADES ACCESSORIES
ENVIRONMENTAL PROTECTION
OPERATING INSTRUCTIONS
MACHINE SET-UP
