manualshive.com logo in svg

Evinrude E-Tec 40 HP, Руководство по обслуживанию, Страница: 37 / 426

Поделиться
Скачать
Evinrude E-Tec 40 HP Скачать руководство пользователя страница 37

35

ROUTINE SERVICE

COOLING SYSTEM

2

Engine Flushing

Flush the outboard with fresh water following each

use in brackish, salt, or polluted water to minimize

the accumulation of scale and silt deposits in cool-

ing system passages.

The outb oard can b e flu shed on th e trailer o r at

dockside; running or not running.

IMPORTANT:

The outboard must be lo cated in

a well ven tilated area with   appropriate grou nd

drainage during the flushing procedure.

Keep  water  inlet pressure   between 20 to 40 p si

(140 to 275 kPa).

Flushing — Outboard Running

Place outboard in VERTICAL (DOWN) position in

a well ventilated area.

Thread garden hose into flushing port.

Turn water supply on.

Run outboard at IDLE only until full operating tem-

perature is reached.

Leave the outbo ard in VERTICAL (DOWN) posi-

tion long enough for the powerhead to drain com-

pletely.

Reinstall propeller.

Flushing — Outboard Not Running

Outboard can  be in  VERTICAL ( DOWN)  or

TILTED (UP) position.

Thread garden hose into flushing port.

Turn water supply ON.

Flush outboard for at least five minutes.

Turn off water supply and remove garden hose.

Leave the outbo ard in VERTICAL (DOWN) posi-

tion long enough for the powerhead to drain com-

pletely.

A

 WARNING

To prevent injury from contact with rotat-
ing propeller, remove the propeller before
flushing.

002024

Содержание E-Tec 40 HP











































































































































































































































































































































































































































Отзывы:

Нет отзывов