Evinox ModuSat FS 150 Скачать руководство пользователя страница 48

Страница: 48 / 50

6.5 Pump Start-up - Wilo PWM Pump

The Wilo Pulse-width modulation (PWM) pump features dry running protection to eliminate

burn out and provides compliance with the 2015 pump efficiency regulations.

Description of the pump

The pump consists of a hydraulic system, a

glandless pump motor with a permanent

magnet rotor, and an electronic control

module with an integrated frequency

converter. The control module provides speed

control by a PWM signal from the ModuSat

control board and indicator LED to display the

pump operating status.

Please note:

When the unit is switched over

to heating mode the pump will run for 2 mins

prior to the heating PICV opening , this is not

a fault in the unit but a normal control function

as the HIU asses the current heating circuit

flow temperature.

Pump LED – Description of Status

LED

Indicators

Diagnosis

Status

Remedy

Lights green

Pump in operation Pump runs

according

its setting

Normal operation

Blinks quick

green

PWM model:

Pump in standby

Normal operation

Blinks red/

green

Pump in function

but stopped

Pump restarts by

itself after the fault

is disappeared

1. Low voltage

U<160 V

High voltage

U>253 V

1. Check voltage

supply

195 V < U < 253 V

2. Module overheating:

temperature

inside motor too

high

2. Check water and

ambient

temperature

Blinks red

Pump out of

function

Pump stopped

(blocked)

Pump does not

restart by itself due

to a permanent failure

Change pump

LED off

No power

No power to pump

1. Pump is not connected

to power supply

1. Check cable

connection

2. LED is damaged

2. Check if pump is

running

3. Electronics are

damaged

Change pump

Содержание ModuSat FS 150



















































Результаты поиска

Содержание ModuSat FS 150

Отзывы:

Бренды по названию

Популярные бренды

Evinox ModuSat FS 150, Руководство по установке

Результаты поиска

Содержание ModuSat FS 150

Отзывы:

Бренды по названию

Популярные бренды