EN
GL
ISH
3
H. POWER INPUT: Connect included power cord to a
grounded outlet in accordance with voltage and frequency
ratings listed on rear panel of amplifier.
I. FUSE: With power disconnected, replace a blown fuse only
with one of the type and rating specified on rear panel of
amplifier.
J. POWER: Turns amp on and off. When first turning amplifier
on, leave OPERATE/STANDBY switch (K) in STANDBY (down)
position for 30 seconds while tubes warm, then set switch
to OPERATE (up) position to take amp out of STANDBY
mode. Before turning POWER switch off (down position),
put amp in STANDBY mode for 10 seconds
K. OPERATE/STANDBY: When taking a break from playing
and before turning amplifier off as noted above (J), put amp
in STANDBY mode—which helps prolong tube life—by
setting this switch to the STANDBY (down) position. Return
switch to OPERATE (up) position when resuming play after
a break. Also as noted above (J), amp should remain in
STANDBY mode for 30 seconds after initial power-up.
L. POWER LEVEL: FULL position provides maximum output
power; 1/4 position reduces power to approximately four watts.
M. EFFECTS LOOP: Connect SEND to effects input and
RETURN to effects output.
N. FOOTSWITCH: Connect included single-button footswitch
here for channel switching (overrides front panel switch).
O. RESONANCE: Adjusts the power amp’s low-frequency
response.
P. LOAD IMPEDANCE: Selects output impedance (4, 8 or 16
ohms) to match speaker load.
Q. SPEAKER OUTPUT: For connection to speaker cabinet.
NOTE: A speaker must always be plugged into the speaker jack
when amplifier is on, or damage may occur. Switch amplifier
off or to STANDBY (K) when changing speaker connections or
impedance settings.
SPECIFICATIONS
Type
PR
3736
Part Numbers
2256000000 (120V, 60Hz)
2256001000 (110V, 60Hz) TW
2256003000 (240V, 50Hz) AUS
2256004000 (230V, 50Hz) UK
2256005000 (220V, 50Hz) ARG
2256006000 (230V, 50Hz) EUR
2256007000 (100V, 50Hz) JPN
2256009000 (220V, 60Hz) ROK
Power Requirement
100 watts
Power Output
15 watts RMS into 4, 8 or 16 ohms
Input Impedance >1MΩ
Output Impedance
4Ω/8Ω/16Ω (selectable)
Fuses
100V units, F1.6A L, 250V
120V units, F1.25A L, 250V
220-240V units, F0.63A L, 250V
Footswitch
Single-button channel-switching footswitch (included)
Tubes
Two EL84 output tubes, five ECC83S preamp tubes
Dimensions
Height: 7” (17.8 cm)
Width: 12.5” (31.2 cm)
Depth: 6” (15.3 cm)
Weight
15 lbs. (6.8 kg)
Product specifications subject to change without notice.
FUSE
POWER
SEND
RETURN
FOOTSWITCH
RESONANCE
IMPEDANCE SPEAKER
OUTPUT
16
Ω
8
Ω
4
Ω
POWER LEVEL
OPERATE
STANDBY
ON
FULL
OFF
INPUT POWER
120V 60Hz
EFFECTS LOOP
15W
4
Ω
min
F1.25A L
250V
FUSE
100W
PANEL REAR EVH 5150 III 15W
7707973000
REV
2.0
REAR PANEL FEATURES
CAUTION: To prevent electric shock hazard, do not connect to mains power supply while top cover is removed.
