background image

- 17 - 

 

A5 

SCSI Reset  

A6 

SCSI Detect 

A7 

SCSI Enable  

A8 

Setup Verifying Password  

A9 

Start of Setup  

AA 

Reserved for ASL (see ASL Status Codes section below)  

AB 

Setup Input Wait  

AC 

Reserved for ASL (see ASL Status Codes section below)  

AD 

Ready To Boot event  

AE 

Legacy Boot event  

AF 

Exit Boot Services event  

B0 

CPU Memory controller configuration 

B1 

Runtime Set Virtual Address MAP End  

B2 

iMC init 

B3 

Memory training 

B4 

Memory training 

B5 

Memory training / timing training 

B6 

Memory training 

B7 

Memory training  

B8-BF 

Memory training / DRAM final configuration 

C0

–CF 

OEM BDS initialization codes  

D0 

CPU initialization error  

D1 

North Bridge initialization error  

D2 

South Bridge initialization error  

D3 

Some of the Architectural Protocols are not available  

D4 

PCI resource allocation error. Out of Resources  

D5 

No Space for Legacy Option ROM  

D6 

No Console Output Devices are found  

D7 

No Console Input Devices are found  

D8 

Invalid password  

D9 

Error loading Boot Option (Load Image returned error)  

DA 

Boot Option is failed (Start Image returned error)  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание X99






















Отзывы: