5
Note:
If no key has been pressed, it will return to MODE 1 automatically after 12
seconds.
While you are setting the sensor, the function of detecting trigger-OFF is set to
disable to avoid false detection (because hands may obstruct the light to
Illumination Sensor during setting). The sensor must be placed still for 12
seconds for the detecting function to be enabled again. If trigger-OFF value is
preset and the sensor is re-powered, it will take 10 seconds before the detecting
function is enabled.
The lux trigger-ON and trigger-OFF cannot be set equal; there MUST be at least
100 LUX differences between them. For example, if now the trigger-ON lux is
already set to be 200 LUX, so trigger-ON lux can only be set
≦
100 LUX or
≧
300 LUX (values between 100 LUX and 300 LUX cannot be set).
2. Countdown Timer
Press
and select MODE 4 to enter setting of countdown time. Icon
flashes and the screen shows the recorded countdown time. If no value is preset,
the screen will display “
- : - -
”.
To adjust countdown time, press and hold
for 5 seconds until a long beep is
sounded. The hour starts flashing.
Use
▲
and
▼
button to adjust the countdown time, and hold
▲
or
▼
button to
scan through the time from 1 hour to 8 hours. Press
to set minutes, and
hold
▲
or
▼
button to scan through the time from 1 minute to 60 minutes. Once
the value is selected, press
to confirm setting or press
ESC/
to cancel.
To clear the last countdown time record, press both
▲
and
▼
at the same time.
The record is cleared after a long beep is sounded.
Countdown timer starts counting ONLY when the trigger-ON lux is triggered. No
response will be made if sensor is triggered ON again during countdown period.
Wait till countdown is completed before restarting the trigger-ON function.
Once countdown is completed, icon
flashes on the screen with LCD backlight
on and 4 continuous beeps sound for 1 second. The sensor will emit RF signal to
the nodes in Grouping 2. The sensor has to be place still for 2 minutes before lux
trigger-ON is enabled again. To clear this restriction, the detected lux of ambient
light during this 2 minutes period MUST be higher than the preset trigger-ON value,
otherwise the sensor will keep recounting the 2 minutes before it can be triggered
again.
Note:
If no key has been pressed, it will return to MODE 1 automatically after 12
seconds.
While you are setting the sensor, the function of detecting trigger-ON is set to
disable to avoid false detection.
The countdown bias is about
±10%.
3. Radio Frequency
This function is designed to enable or disable the sending function of RF command
to the associated nodes in Grouping 2 once Illumination Sensor has been triggered
ON/OFF.
Press
and select MODE 5, the icon
should flash. Press
▲
to turn On
(enable) the function or
▼
to turn OFF (disable) the function.
Note:
If RF mode is OFF, no command will be sent even the Illumination Sensor has
been triggered.
If the RF reading is 00, it implies no node ID has been allocated by Z-Wave
Controller. Please execute inclusion mode as described on page 1.
4. Beep Tone
To set the beep tone, press
and select MODE 6. The icon
flashes. Press
▲
for ON and
▼
for OFF. If it is ON, a beep tone will be sounded whenever a
button is pressed; 4 continuous beeps will be sounded for 1 second if the sensor
has been triggered.
Programming
1. Z-Wave’s Groups (Association Command Class Version 2)
The Illumination Sensor can be set to send reports to or control associated Z-Wave
devices. It supports two association groups with one node support for Grouping 1
and three nodes support for Grouping 2.
Grouping 1 includes POWER_APPLIED, SENSOR_MULTILEVEL _REPORT,
Hour
Minute
