Everwin PN57 Series Скачать руководство пользователя страница 11

 

11 

TOOL OPERATION CHECK 

 

CAUTION: Remove all fasteners from tool before performing tool operation check. 

 

1.  CONTACT TRIP OPERATION: 

 

a.  With finger off the trigger, press the contact trip against the work surface. 

THE TOOL MUST NOT CYCLE. 

 

b.  Hold the tool off the work surface, and pull the trigger. 

THE TOOL MUST NOT CYCLE.

 

c.  With  the  tool  off  the  work  surface,  pull  the  trigger.  Press  the  contact  trip  against  the  work 

surface. 

THE TOOL MUST CYCLE.

 

d.  Without touching the trigger, press the contact trip against the work surface, then pull the 

trigger. 

THE TOOL MUST CYCLE. 

 

2.  SEQUENTIAL TRIP OPERATION: 

 

a.  Press the contact trip against the work surface, without touching the trigger. 

THE TOOL MUST NOT CYCLE.

 

b.  Hold the tool off the work surface and pull the trigger.

 

THE TOOL MUST NOT CYCLE.

 

Release the trigger. The trigger must return to the trigger stop on the frame. 

c.  Pull the trigger and press the contact trip against the work surface. 

THE TOOL MUST NOT CYCLE.

 

d.  With finger off the trigger, press the contact trip against the work surface. Pull the trigger. 

THE TOOL MUST CYCLE. 
 

IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR 

SAFE OPERATION 

 

l

 

Use this pneumatic tool only for the purpose for which it was designed like pallet, crating, sheathing, 
decking applications

 

l

 

Never use this tool in a manner that could cause a fastener to be directed toward the user or others in 
the work area.

 

l

 

Do not use the tool as a hammer.

 

l

 

Always carry the tool by the handle. Never carry the tool by the air hose.

 

l

 

Do not carry this tool with the trigger depressed when not in use

l

 

Do not alter or modify this tool from the original design or function.

 

l

 

Always be aware that misuse and improper handling of this tool can cause injury to yourself and 
others.

 

l

 

Never clamp or tape the trigger or contact trip in an actuated position.

 

l

 

Never leave a tool unattended with the air hose attached.

 

l

 

Do not operate this tool if it does not contain a legible WARNING LABEL.

 

l

 

Do not continue to use a tool that leaks air or does not function properly. Notify your distributor 
or representative if your tool continues to experience functional problems.

 

 

Содержание PN57 Series













Отзывы: