
XRF1/XRF1A 16x16 RF Router Manual
XRF1 - 6-4
Revision 1.2
VISTALINK
Once a session is initiated, the left hand window of the X-NCP2 will display the type of router connected
(i.e. XRF1 Router) and the range of available inputs and outputs. The right-hand window will show the
current status of input and output routes (destination select mode). Rotating any of the shaft encoders will
increment the crosspoint displayed in the order of the outputs.
6.1.8. Terminating a Control Session with an XRF1
To manually terminate a session at any time, simultaneously press the [
↑
] and [
↓
] keys to return to the list
of router IP addresses.
6.1.8.1.
Controlling Crosspoints Using the X-NCP2
Once a session is initiated, crosspoint changes may be made by using the [Output Select] and [Input
Select] buttons, followed by the [TAKE] button. As an alternative to using the pushbuttons for input and
output selection, the scroll knobs on either side of the display may be used for output and input selection,
followed by the [TAKE] button.
The examples listed below illustrate two different methods of initiating a crosspoint take with the router.
Both examples illustrate making a connection between output 5 and input 2.
6.1.8.2.
Example 1: Pushbutton control to switch input 2 to output 5
1) Initiate a panel session by highlighting the IP address (or router name) of the router in the display
area of the panel. This is done using the leftmost scroll knob. When the frame IP address (or
name) is highlighted, press [SELECT].
2) Press [OUTPUT SELECT] to put the panel into output selection mode. The numeric buttons 0-9 will
illuminate.
3) Use the numeric buttons to select the desired output (i.e. 5) by pressing [5], followed by [OUTPUT
SELECT] to exit output selection mode.
4) Press [INPUT SELECT] to put the panel into input selection mode. The numeric buttons 0-9 will
illuminate.
5) Use the numeric buttons to select the desired input (i.e. 2) by pressing [2], followed by [INPUT
SELECT] to exit the input selection mode.
6) Press [TAKE]. The panel display will display the input and output selected, plus a “take successful”
message. The router does not perform the input to output connection until the [TAKE] button is
pressed.
In short, the steps are [SELECT], [OUTPUT SELECT], [2], [OUTPUT SELECT], [INPUT SELECT], [2],
[INPUT SELECT], [TAKE].
"
NOTE: The control panel session will time out after approximately 30 seconds of
no panel activity.
6.1.8.3.
Example 2: Rotary knob control to switch input 2 to output 5
1. Initiate a panel session by highlighting the IP address (or router name) of the router in the display
area of the panel. This is done using the leftmost scroll knob. When the frame IP address (or
name) is highlighted, press [SELECT].
2. Use the left scroll knob (of the right side display area) to select an output. As you scroll through
the system outputs, the current input connection is displayed.
3. Use the right
knob to select the desired input.
Содержание XRF1
