manualshive.com logo in svg

evertz 78908MG-10GE2, Руководство пользователя, Страница: 47 / 52

Поделиться
Скачать
evertz 78908MG-10GE2 Скачать руководство пользователя страница 47

7890MG Series 

Universal Media over IP Gateway for 10 x ASI/SD/HD/3G/GE

 

WEBEASY

®

 

  

Revision 0.2

 

Page - 39 

Trap 

Video Input Loss: 

Triggers when video was previously present, and has now ceased to be. If there 

is no video present, this will be red.

 

 
Video Input Error: 

Triggers when there is an video error detected on the input. 

 
Video Input Standard Change: 

Triggers when the video Input Standard has changed.

 

 
Video Input ASI Over Bandwidth: 

Triggers when the input ASI stream is over the bandwidth setting 

located in the Input tab. 

 
Video ASI Input CC Error: 

Triggers when Continuity Count Errors on ASI Video. 

 

Video ASI Input Sync Error: 

Triggers when Sync Error on ASI Video. 

 
Video Input Type Mismatch: 

Triggers when the video input does not match ‘Video Pass Type’ 

under the ‘Input’ TAB. 

 
Video Input Type Change: 

Triggers when the video input format has changed. 

 

Trunk A Tx Stream IP Change: 

Triggers when any changes have occurred to the settings on this 

stream for Trunk A. 

 
Trunk B Tx Stream IP Change: 

Triggers when any changes have occurred to the settings on this 

stream for Trunk B.

 

 
Port Select: 

Brings up the Output Fault SNMP Error Traps for each Access Port.  The check boxes on 

the left will enable or disable these faults from being sent to the SNMP Fault Trap log. 

 
Traps 

Video Output Loss:

 Triggers when video was present and is now Lost. When no video is present, 

this indicator will be red.

 

 
Video Output Error: 

Triggers when the video output has errors. 

 
Video Output Standard Change: 

Triggers when the video output standard has changed.

 

 
Trunk A In Use: 

Triggers when the incoming IP stream on Trunk A is in use for this port.

 

 
Trunk B In Use: 

Triggers when the incoming IP stream on Trunk B is in use for this port. 

 
Video Stream Sequence Error: 

Triggers when there is a video output sequence count error. 

 
Video Stream Crc Error: 

Triggers when there is a Video Output CRC Error. 

 
Video ASI Output CC Error: 

Triggers when there is an ASI Continuity Count Error detected on 

output. 

 
Video ASI Output Sync Error: 

Triggers when there is an ASI Sync Error Fault. 

 

Содержание 78908MG-10GE2





















































Отзывы:

Нет отзывов