evertz 7700 Series Скачать руководство пользователя страница 87

Страница: 87 / 94

7700 MultiFrame Manual

7736CEM Composite Encoder with Monitoring

Revision 1.5

Page - 77

*Grey background indicates un-implemented or un-tested features

8.9.8. Setting the Blink Mode of the Fault Windows

This parameter determines if the Fault 1 window will blink or be on solid when the fault is active.

When it is set to

Disable

the fault window will be on steady when it is active.

When it is set to

Enable

the fault window will blink when it is active.

8.10. FAULT TRAPS

The

Fault

Traps

tab, as illustrated in Figure 8-12, allows the user to enable or disable traps and view trap

status. To enable a particular trap, simply click the box located beside each trap so that a check-mark
appears. When a check-mark is present, the trap is enabled. When a check-mark is not present, the trap
is disabled.

The

Trap Status

section displays whether a fault is active or not. If the box is green, then the

corresponding trap is not active. If the box is red, then the corresponding trap is active.

Figure 8-12: Fault Traps Tab

Содержание 7700 Series































































































Результаты поиска

Содержание 7700 Series

Отзывы:

Похожие инструкции для 7700 Series

Бренды по названию

Популярные бренды

evertz 7700 Series, Руководство пользователя

Результаты поиска

Содержание 7700 Series

Отзывы:

Похожие инструкции для 7700 Series

Бренды по названию

Популярные бренды