evertz 7700 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 94

background image

7700 MultiFrame Manual
7736CEM Composite Encoder with Monitoring

Page - 28

Revision 1.5

*Grey background indicates un-implemented or un-tested features

7.6.1. Adding the NTSC Setup Pedestal

Video/SID

Composite NTSC analog video may have a 7.5 IRE pedestal while
4:2:2 SDI video does not. This control, when set to

On

, will add the

pedestal and re-scale the video accordingly. The setup pedestal
should not be present on composite video when operating in Japan.

Video Processing

NTSC setup
pedestal

Off
On

7.6.2. Line 21 Processing

Video/SID

Closed captioning has been defined to NOT have a 7.5 IRE pedestal,
but it is placed on the first active line of video where there may be a
pedestal. The upstream closed captioning encoder should not have
generated a setup pedestal. When encoding composite video with
properly keyed captioning, a pedestal must not be generated.

This control, when set to

Off

, will not create the 7.5 IRE pedestal on

line 21. This is the default state for properly generated captioning.

When set to

On

, the 7.5 IRE pedestal will be generated on line 21.

Use this state when there are no input captions.

Note: The

On

condition will only take effect if the

NTSC Setup

Pedestal

control is set to

On

.

Blank

is used to remove captioning from line 21.

If you need independent field 1 and field 2 on/off control of setup, set
this control to

Off

and then use the controls in the

VBI Processing

Menu.

Note: The captions are

Blank

ed from the main, high quality, output

only. This will allow the monitoring of upstream captioning on the

monitoring output

even when it is not desirable to have them passed

downstream on the program video.

Video Processing

Line 21 setup

Off,
On,
Blank

7.6.3. Colour Bars

Video/SID

Internally generated colour bars may be turned on to aid in monitor
calibration. To make sure that this control is not left on accidentally,
this parameter is not included in the preset management.

Warning: You cannot change the output phasing when the colour bars
are turned on. Be careful when adjusting genlock references when this
is turned on.

Video Processing

Colour bars

On,
Off

«
...
36
37
38
39
40
...
»

Содержание 7700 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для 7700 Series

NA-P 500 - AMPLIFIER

Бренд: NAIM Страницы: 15

Бренд: NAIM Страницы: 32

Бренд: NAIM Страницы: 24

Бренд: NAIM Страницы: 40

Бренд: NAIM Страницы: 32

Бренд: B&K Страницы: 15

Бренд: Marshall Amplification Страницы: 12

Бренд: Arcam Страницы: 84

Бренд: Xicom Страницы: 168

Бренд: Velleman-Kit Страницы: 24

Бренд: Fortin Страницы: 12

Бренд: Parallel Audio Страницы: 12

Subwoofer Gadget

Бренд: Natural Bass Technology Страницы: 2

Stereo 40i Classic EL34

Бренд: icon Audio Страницы: 8

Бренд: SY Electronics Страницы: 12

Бренд: Ayre Страницы: 24

Бренд: HEED Страницы: 2

Бренд: M-system Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды