evertz 7700 Series Скачать руководство пользователя страница 1

Страница: 1 / 94

7700 MultiFrame Manual

7736CEM Composite Encoder with Monitoring

Revision 1.5

*Grey background indicates un-implemented or un-tested features

TABLE OF CONTENTS

OVERVIEW ....................................................................................................................................... 1

1.1.

FUNCTIONAL DESCRIPTION .................................................................................................. 2

INSTALLATION ................................................................................................................................. 5

2.1.

VIDEO IN AND OUT ................................................................................................................. 5

SPECIFICATIONS ............................................................................................................................. 6

3.1.

SERIAL VIDEO INPUT ............................................................................................................. 6

3.2.

ANALOG BROADCAST VIDEO OUTPUT ................................................................................ 6

3.3.

REFERENCE VIDEO INPUT .................................................................................................... 7

3.4.

ANALOG MONITORING VIDEO OUTPUT ............................................................................... 7

3.5.

ANALOG AUDIO OUTPUTS (-A4 ONLY) ................................................................................. 7

3.6.

UNBALANCED AES AUDIO INPUTS (-A4 ONLY) ................................................................... 8

3.7.

BALANCED AES AUDIO INPUTS (-A4-B ONLY) .................................................................... 8

3.8.

ELECTRICAL ........................................................................................................................... 8

3.9.

PHYSICAL ................................................................................................................................ 8

STATUS LEDS .................................................................................................................................. 9

4.1.

MODULE STATUS LEDS ......................................................................................................... 9

4.2.

AUDIO STATUS LEDS ........................................................................................................... 10

AUDIO LEVELS, HEADROOM, CLIPPING AND THE BAR GRAPHS ............................................ 11

AUDIO ALARM CALIBRATION PROCEDURE ............................................................................... 12

6.1.

CALIBRATE AUDIO SILENCE DETECTION .......................................................................... 12

6.2.

CALIBRATE AUDIO PHASE REVERSAL DETECTION ......................................................... 12

6.3.

CALIBRATE AUDIO MONO DETECTION .............................................................................. 12

6.4.

DEFINE THE FAULT CONDITION(S) ..................................................................................... 13

Содержание 7700 Series































































































Результаты поиска

Содержание 7700 Series

Отзывы:

Похожие инструкции для 7700 Series

Бренды по названию

Популярные бренды

evertz 7700 Series, Руководство пользователя

Результаты поиска

Содержание 7700 Series

Отзывы:

Похожие инструкции для 7700 Series

Бренды по названию

Популярные бренды