EverFocus ES0812-31 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

background image

PoE Switch

16

4.2.1.4

Firmware Update

Before the firmware update procedure is executed, you should enter the
password twice and then press

Update

button.

Figure 2-5

The popup warning window appears for making sure you want to proceed the
firmware upgrading process.

Notice that the code of flash memory will be erased.

All functions will be detected except the firmware update itself.

If want proceed, click “

Yes

” to continue. If not, please click “

Cancel

”.

Figure 2-6

The smart switch will erase the flash memory. There is a self-protection
mechanism in the Boot Loader, so the Boot Loader will keep intact. Even though
the power is turned off or the cable link fails during the firmware update
procedure, the Boot loader will restore the code to firmware update page.

«
...
19
20
21
22
23
...
»

Содержание ES0812-31

























































Отзывы:

Нет отзывов

Похожие инструкции для ES0812-31

Бренд: H3C Страницы: 38

Бренд: H3C Страницы: 36

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 36

S12500X-AF Series

Бренд: H3C Страницы: 21

S12500X-AF Series

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 16

Бренд: H-Tronic Страницы: 32

Бренд: WAGO Страницы: 39

Бренд: Festo Страницы: 2

Бренд: IPGARD Страницы: 2

START-LINE AGC-3500

Бренд: Trust Страницы: 16

Бренд: Cabletron Systems Страницы: 110

Бренд: ATEN Страницы: 2

Бренд: Pulse-Eight Страницы: 9

Бренд: Sunix Страницы: 55

Бренд: LevelOne Страницы: 35

Hi-Speed USB 4-Port Bay Hub

Бренд: SIIG Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды