Evco c-pro 3 hecto Скачать руководство пользователя страница 39

Страница: 39 / 86

EVCO S.p.A.

c-pro 3

| Hardware manual ver. 2.0 | Code 114CP3E204

page 39 of 86

CAN

LED CANbus communication

if it is lit, the device will be configured to communicate via CANbus with another device but the CAN communication

will not have been set up

if it flashes slowly, the CANbus communication will have been set up but it will not be completely correct

if it flashes quickly, the CANbus communication will have been set up and will be correct

if it is out, no CANbus communication will be running

LED auxiliary (not used in

c-pro 3

hecto

, in

c-pro 3

hecto+

, in

c-pro 3

EXP hecto

and in

c-pro 3

EXP hecto

)

The operation of this LED can be programmed through the development environment UNI-PRO 3

5.2.2. LEDs on the RS-485 ports

The following drawing shows the aspect of a RS-485 port.

The following table shows the meaning of the LEDs on the RS-485 ports.

LED

Meaning

red LED

LED error

if it is lit, an internal error will have arisen

if it flashes quickly, a configuration error will have arisen

if it is out, no error will be running

yellow LED

LED Modbus communication

if it is lit, no Modbus communication will be running

if it flashes quickly, the Modbus communication will have been set up and will be correct

if it is out, the controller will not be configured to communicate via Modbus

Содержание c-pro 3 hecto























































































Результаты поиска

Содержание c-pro 3 hecto

Отзывы:

Evco c-pro 3 hecto, Руководство по оборудованию, Страница: 39 / 86

Результаты поиска

Содержание c-pro 3 hecto

Отзывы: