EUTECH INSTRUMENTS CyberScan pH 10 Скачать руководство пользователя страница 55

Страница: 55 / 67

12 ERROR

MESSAGES

The following table provides a guideline to enable diagnosis of possible problems indicated by

the messages generated by the CyberScan meter. The table also provides possible solutions

to the problems encountered.

ERROR MESSAGE

INDICATES

POSSIBLE CAUSE

CORRECTIVE
ACTION

Err. 1 (in primary
display)

Memory write error

Instrument too old (> 10
years) or hardware
failure.

Turn OFF meter and
turn it ON. Return to
dealer if necessary.

Err. 2 (in primary
display)

Memory checksum error

Hardware failure.

Turn OFF meter and
turn it ON. Return to
dealer if necessary.

Err. 3 (in primary
display)

ADC error

Hardware error.

Turn OFF meter and
turn it ON. Return to
dealer if necessary.

Err. 4 (in primary
display)

Keypad error

One or more keys on the
keypad are stuck.

Turn OFF meter and
turn it ON. Return to
dealer if necessary.

Err. Annunciator

Wrong keypad input

Wrong input in selected
mode.

Release key. Select
valid operations
depending on mode.

Electrode icon & buffer
icon blinks & Err
annunciator lights up

Calibration

Incorrect buffer used or
contaminated buffer
solution

Check if the right buffer
was selected or use
fresh buffer solution.

Battery icon lights up

Low Battery

Battery power is low

Replace batteries with
fresh ones as soon as
possible.

Содержание CyberScan pH 10




































































Результаты поиска

Содержание CyberScan pH 10

Отзывы:

EUTECH INSTRUMENTS CyberScan pH 10, Инструкция по эксплуатации, Страница: 55 / 67

Результаты поиска

Содержание CyberScan pH 10

Отзывы: