EUTECH INSTRUMENTS CyberScan pH 10 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 67

EUTECH INSTRUMENTS CyberScan pH 10 Скачать руководство пользователя страница 23

19

5 MEASUREMENT

This meter is capable of taking measurements with automatic or manual temperature

compensation. Automatic temperature compensation only occurs when a temperature sensor

is plugged into the meter. If there is no temperature sensor plugged into the meter, the default

manual temperature setting is automatically 25.0 °C. You can manually set the temperature to

match your working conditions using a separate thermometer.

NOTE: Remove the protective rubber cap or soaker bottle of the electrode before proceeding

with measurement. Take care not to exert too much force as this may cause damage to the

electrode.

5.1

Automatic Temperature Compensation

For automatic temperature compensation

(ATC) simply plug the temperature probe

into the meter. The ATC indicator will light

up on the LCD.

NOTE: If you are using a temperature

probe, the probe must be submersed in the

liquid you are measuring.

Figure 21: ATC annunciator will light up when

connected to temperature probe

«
...
21
22
23
24
25
...
»

Содержание CyberScan pH 10




































































Отзывы:

Нет отзывов