manualshive.com logo in svg

Euroheat Nestor Martin IT33, Руководство по эксплуатации

Поделиться
Скачать
Euroheat Nestor Martin IT33 Скачать руководство пользователя страница 27

© 

EUROHEAT

 DISTRIBUTORS (H.B.S) LTD. April. 2011

    

 Instructions Part Number IN1176 Ed.B

27

Cleaning The Insert

Cleaning The Glass

Properly operated, with the correct fuel, your glass will remain clean.  Slight staining  may appear when the insert 
is lit and below its operating temperature. This will normally clear as the insert’s temperature rises. 
If it becomes necessary to clean the glass by hand do not attempt to do so unless the insert is cold. Proprietary 
glass cleaning agents are available but they must specifically state its suitability for insert glass before being used 
because the glass in you insert is not ordinary glass and may be damaged with an unsuitable cleaner.
Newspaper moistened with water to which a little vinegar has been added will normally remove most staining, 
but for really stubborn marks, gentle polishing with fine steel wool lubricated with a few drops of dish washing 
detergent will need to be employed. Great care must be taken not to clean the glass too vigorously as particles 
of grit may have adhered with the stain and these could cause scratching if dragged across the glass. However 
well the insert burns it will eventually become necessary to clean the glass, but if cleaning becomes necessary 
too often we advise you to review your operating procedures to determine whether cleaner and more efficient 
combustion can be achieved.

The Insert Body

Dusting the insert may be carried out when the insert is at its minimum heat output temperature, using light 
strokes of a real bristle paint brush. Thorough cleaning, or any attempt to remove marks on the insert body must 
only be done when the insert is cold.
Inserts with a painted black finish should never be cleaned with a cloth as the texture of the paint will abrade and 
collect lint from the cloth which will be almost impossible to remove. Vigorous brushing with a stiff real bristle 
paint brush will remove all dust, but where the paint is marked, the stains are better obliterated with a spray of 
suitable insert paint rather than attempts made to clean them off. Suitable paint may be purchased from a insert 
shop or direct from Euroheat. 

The Flue

Even if your flue is correctly lined it is advisable to run your insert at a high setting to thoroughly warm the flue 
periodically and ensure it is swept regularly.  If the insert has not been used for some time it will be necessary 
to ensure the flue has not been blocked with twigs from home building birds or blocked with other obstructions 
before the insert is lit. Lighting a small piece of paper within the insert will determine the flue’s ability to remove 
any products of combustion.

  
National Chimney Sweeps Association  

01785 811732   

The Solid Fuel Association    

 

0845 6014406 .

Содержание Nestor Martin IT33

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды